
A combi boiler vs heat-only boiler choice comes down to how your household uses hot water and how much room you have. A combi heats the house and makes hot water on demand in one unit, while a heat-only boiler heats the radiators and usually feeds a separate stored-water tank. Here is how the two compare, so you can weigh them before a quote or a boiler installation.
Key takeaways
- A combi heats radiators and makes hot water on demand, with no tank.
- A heat-only boiler heats the radiators, and an indirect tank or separate water heater supplies hot water.
- Households that run two showers at once often do better with stored hot water.
- A combi saves space but ties heating and hot water to one unit.
- Sizing comes from a heat-loss calculation, not the old boiler’s label.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- What a combi boiler is
- What a heat-only boiler is
- Combi boiler vs heat-only boiler: hot water in daily use
- Combi boiler vs heat-only boiler: space and layout
- Reliability and repairs: what happens when something fails
- Running costs and efficiency
- Combi boiler vs heat-only boiler: which suits your household?
- Switching from an older boiler system
- Combi boiler vs heat-only boiler: what installation involves
- Gas and carbon monoxide safety with either type
- Getting the right advice before you decide
- Combi boiler vs heat-only boiler: common questions
What a combi boiler is
A combi boiler, short for combination boiler, is one compact unit that does two jobs: it heats water for the radiators and it heats tap water the moment you open a hot tap. There is no storage tank. When the tap opens, the boiler switches from heating to hot water, and it switches back when the tap closes.
That design is why combis take up little room. They are usually wall-hung and can replace both an old boiler and a separate water heater with one appliance.
What a heat-only boiler is
A heat-only boiler heats water for the radiators and in-floor loops, and nothing else. If you want hot water for taps as well, it is paired with an indirect tank, a stored-water cylinder heated by the boiler through a coil. The boiler warms the tank, and the tank holds the hot water until you need it.
You will also hear the term system boiler, which is a heat-only boiler with some of the pumps and controls built in. For the purposes of hot water, it works the same way: the heat comes from the boiler and the storage comes from the tank.
Combi boiler vs heat-only boiler: hot water in daily use
The biggest everyday difference between a combi boiler vs heat-only boiler setup is how hot water is delivered. A combi makes it as you use it, so the supply never runs out but the flow is limited by the boiler’s output. A tank stores a volume that can serve several taps at once, until it is used up and has to reheat.
Cold winter inlet water makes a difference too. The colder the water coming into the house, the more work a combi has to do to heat it, so the flow you get at the tap can drop in January.
| Situation | Combi boiler | Heat-only boiler with indirect tank |
|---|---|---|
| One shower, mid-morning | Steady hot water for as long as it runs | Plenty from the tank |
| Two showers at once | Flow can drop at each, depending on the unit | The tank usually covers both for a while |
| Back-to-back baths | Never runs out, but filling is slower | Can run low until the tank reheats |
| Heating and hot water together | Heating can pause while a tap runs | Both can run, with the tank topped up by the boiler |
| A tap used for a minute | A short wait for hot water to arrive | Hot water is already stored |
Combi boiler vs heat-only boiler: space and layout
A combi saves floor space because there is no tank to fit, which matters in a tight basement, a closet or a small mechanical room. It can also free the spot where a hot water tank used to stand. A heat-only boiler needs room for both the boiler and the tank, plus the pipes joining them.
Layout matters beyond space. A combi needs the hot water pipes to reach the taps from one point, and long runs can mean a wait. Older homes with a boiler and radiators can take either type, but the venting and piping options differ, which a technician checks on site.
Reliability and repairs: what happens when something fails
With a combi, one unit supplies both heat and hot water, so a failure can mean no heat and no hot water at once. A heat-only boiler with a separate tank spreads the risk a little: the tank keeps its stored hot water for a while after the boiler stops, so a morning shower is not always lost.
A combi also has more parts working in a small space, including a plate heat exchanger for tap water that can scale up with hard water, which is common across the GTA. A heat-only boiler has fewer moving parts of its own. Either type should be serviced yearly, and our boiler repair page covers what we repair.
Running costs and efficiency
Both types come in condensing models rated 90% AFUE or higher, and a condensing boiler of either kind can be far more efficient than an old cast iron unit when the system runs at the low return temperatures condensing needs. The efficiency number on its own does not decide which is cheaper to run, because costs depend on how you use hot water and how well the system is set up.
A combi has no tank to lose heat while it sits, which helps in a small household. A tank loses a little heat even when well insulated, but it can use the boiler more steadily. A technician can explain the trade-offs for your home, and we give a flat-rate price before work, not a cost guess.
Combi boiler vs heat-only boiler: which suits your household?
A combi tends to suit smaller households, one or two bathrooms and homes short on space. A heat-only boiler with a tank tends to suit larger families, several bathrooms and busy mornings. These are tendencies, not rules, and your own habits count for more than the house size.
- One or two people showering at different times usually points to a combi.
- Two or more showers at once usually points to a tank.
- A tight basement or no spare wall space usually points to a combi.
- A big soaking tub that fills fast usually points to a tank.
- A wish for a backup hot water source usually points to a tank.
Switching from an older boiler system
Changing type is possible, but it is a design decision, not a swap. Moving from a heat-only boiler with a tank to a combi removes the tank and changes how hot water is delivered. Moving the other way means finding room for a tank. Existing radiators usually keep working with a new boiler.
Older systems can also need changes to venting and near-boiler piping. Sizing comes from a room-by-room heat-loss calculation, not the old unit’s rating, and the hot water side is sized to the household. That’s why the choice is best made with a technician in the house.
Combi boiler vs heat-only boiler: what installation involves
Installing either type is gas work and needs a licensed technician, along with the permits and inspections the job calls for. Our TSSA-certified gas technicians fit both, and all major brands are serviced. The install covers the boiler, the venting, the condensate drain, the gas connection and the piping.
A heat-only boiler adds the indirect tank, its piping and controls. A combi adds the tap water connection and a pressure check on the cold supply. We handle the permits and inspections the job needs, and you approve a flat-rate price before work begins.
Gas and carbon monoxide safety with either type
Both types burn natural gas, so the same safety rules apply to each. If you ever smell gas, walk out of the house at once. Don’t flip a switch or use a phone inside, and call Enbridge Gas on 1-866-763-5427 when you are clear of the building.
Fit carbon monoxide alarms as Ontario requires for homes with a fuel-burning appliance, a fireplace or an attached garage: next to every sleeping area and, since January 1, 2026, on every storey. If one sounds, get everyone outdoors, pets included, and call 911. The Ontario carbon monoxide safety page (opens in a new tab) lists where alarms belong.
Getting the right advice before you decide
The right choice comes from a visit, not a brochure, because the technician can see the space, the radiators, the piping and how many people live in the house. Bring a list of how you use hot water, and any problems with your current system.
A yearly check under the maintenance plan keeps either type running well. If you’re weighing options for a home in the north of the GTA, see boiler repair in Markham, or contact us to book.
Combi boiler vs heat-only boiler: common questions
Is a combi boiler better than a heat-only boiler?
Neither is better in every home. A combi saves space and gives hot water on demand, which suits smaller households. A heat-only boiler with a tank handles several showers at once, which suits larger ones. The right pick depends on how many people use hot water and when.
Can a combi boiler run two showers at once?
It can, but the flow at each shower may drop, because one unit is heating all the water as it flows. How much depends on the unit’s output and the temperature of the incoming water. If two showers at once is routine, a tank is usually the safer choice.
What is an indirect tank?
It’s a stored-water tank with a coil inside, heated by the boiler rather than by its own burner or element. The boiler warms the coil, the coil warms the water, and the tank holds it until you use it. It pairs with a heat-only or system boiler.
What happens to my radiators if I switch to a combi?
Existing radiators usually keep working with a new condensing boiler of either type. A technician checks the radiators, pipes and venting first. Radiators sized for an old high-temperature boiler may need a closer look so the new boiler can run efficiently, and we say so before quoting.
Does a combi boiler still give hot water if the boiler fails?
No. A combi makes hot water only when the boiler runs, so a boiler fault can mean no heat and no hot water. A tank can hold stored hot water for a while, and some tanks have another way to heat, which gives a heat-only setup more resilience.
Does hard water affect a combi boiler?
It can. Tap water passes through a small heat exchanger in a combi, and minerals can scale it up over time, which cuts the hot water flow. Hard water is common across the GTA, so yearly servicing matters, and a technician can check the exchanger.
Can I fit a combi boiler where my old boiler and tank were?
Often yes, and it frees the space the tank took. It depends on the gas supply, the venting route, the cold water supply and the piping. A technician checks all four on a visit before recommending anything or quoting a price.
Who installs and repairs boilers in the GTA?
The TSSA-certified gas technicians at Assurance HVAC Heating & Cooling install and repair both types in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. A flat-rate price is yours to approve first, and a written workmanship warranty backs the work. Calls are answered 24/7.
Planning a replacement? We’ll call you back to book a quote visit.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
