
Boiler repair in Toronto and the GTA
(647) 692-0819Open 24/7, day or night
Assurance HVAC Heating & Cooling provides boiler repair in Toronto for radiators, in-floor heat and combi boilers, with TSSA-certified gas technicians available 24/7. Call us or book a repair online, and you get a flat-rate price before any work starts. We service all major brands, from cast iron boilers in century homes to wall-hung combi units in Toronto semis and townhouses, and most repairs are done on the first visit when the part is on the truck.
Key takeaways
- Repairs for radiators, in-floor radiant heat and combi boilers, with all major brands serviced.
- TSSA-certified G2 and G1 gas technicians handle every gas repair.
- A flat-rate price after the diagnosis, and nothing starts until you approve it.
- Open 24/7: no-heat and no-hot-water emergencies go to the front of the line.
- Toronto, from the Annex to Scarborough, plus 11 more areas across the GTA.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- Signs you need boiler repair in Toronto
- Quick checks before you call for boiler service
- Why are my radiators cold? What each pattern means
- Radiator repair in Toronto’s century homes
- Common boiler problems, causes and fixes
- Boiler pressure too high or too low
- Combi boiler repair: no hot water, or hot water but no heat
- In-floor radiant heat and hydronic heating repair
- Boiler repair in Toronto: what happens on a visit
- Emergency boiler repair in Toronto: what to do first
- Boiler safety: carbon monoxide alarms and TSSA
- Should you repair or replace your boiler?
- What affects the cost of boiler repair in Toronto?
- Annual boiler service and maintenance
- Boiler repair across Toronto’s neighbourhoods
- Boilers and radiant heat questions
Signs you need boiler repair in Toronto
Book a repair when radiators stay cold, the system bangs or kettles, the pressure gauge sits outside its normal range, water appears around the boiler or a combi stops making hot water. In a Toronto winter these faults get worse, and cost more to fix, the longer the boiler runs with them.
- Radiators cold at the top, the bottom or on the top floor
- Banging, gurgling or a kettling rumble
- A pressure gauge well above or below its usual reading
- Water around the boiler, a pipe joint, a pump or a radiator valve
- Repeated lockouts, fault codes or short cycling on and off
- Soot, scorch marks or a yellow, lazy flame instead of a steady blue one
Soot, a yellow flame, water from the relief valve or a gauge in the red: switch the boiler off and call us now.
Quick checks before you call for boiler service
A few safe checks can solve a no-heat call or give the technician a head start: the thermostat, the power, the pressure gauge and, on a high-efficiency boiler, the vent pipes and the condensate drain. Anything inside the burner or electrical compartments is a job for a licensed gas technician.
- Thermostat: set to Heat, above room temperature, batteries checked
- Breaker: reset a tripped breaker once; if it trips again, call
- Service switch: make sure it’s on, then turn it off and on once
- Pressure gauge: write down the reading
- Vent pipes: after a Toronto snowfall, clear side-wall vents by hand
- Condensate drain: look for a kink, a visible clog or pooling water
Refill the pressure only if your boiler’s manual tells the owner how. Never open sealed compartments, reset internal safety controls, touch the gas valve, or cap a relief valve. Note any fault code; the technician reads it on site.
Why are my radiators cold? What each pattern means
Where the cold spot sits tells you a lot about cold radiators. Cold at the top usually means trapped air, cold at the bottom points to sludge, one cold room often means a closed or seized valve, and cold top-floor rooms in a tall Toronto house can mean the pressure is too low to lift water that high.
| What you notice | Likely cause | What fixes it |
|---|---|---|
| Cold at the top, warm at the bottom | Trapped air | Bleeding, then a pressure check |
| Warm at the top, cold at the bottom | Sludge or rust settled inside | Flushing the radiator or system |
| One radiator cold | A closed or seized valve, or an air lock | Freeing or replacing the valve |
| Top-floor radiators cold | Low pressure or air high up | Finding the pressure loss |
| One zone cold | A stuck zone valve or zone pump | Replacing the actuator or pump |
| Every radiator cold | No firing, a failed circulator or a control fault | Diagnosis at the boiler |
Radiator repair in Toronto’s century homes
Radiator repair usually means fixing the system around the radiators: freeing a seized valve, replacing a leaking valve or bleed screw, flushing out sludge, or balancing the flow so the far rooms heat as well as the near ones. Cast iron radiators rarely wear out, which is why so many older Toronto homes still rely on them.
Houses in the Annex, Cabbagetown and Riverdale often have radiators that have outlasted several boilers. Hydronic homes rarely have ducts, so ductless heat pumps are the usual way to add cooling, and they heat too.
Common boiler problems, causes and fixes
Most boiler calls come down to a handful of faults: trapped air, pressure problems, a failed circulator pump or zone valve, scale in the heat exchanger, an ignition or flame-sensing fault, or a blocked condensate line on a high-efficiency boiler. Here is what each symptom usually means and how it gets fixed.
| Symptom | Likely cause | Usual fix |
|---|---|---|
| Kettling or banging | Scale or sludge on the heat exchanger | Flushing the system and checking the pump |
| Leak at a joint, pump or valve | Worn seals or corrosion | Replacing the seal, valve or fitting |
| Lockout or fault code | Ignition, flame sensing, venting or a blocked condensate line | Cleaning or replacing the part and testing combustion |
| Shuts down in a cold snap | Vents blocked by snow or ice, or a frozen condensate line | Clearing the vent and drain, then finding why it froze |
| Short cycling | An oversized boiler, a control setting or poor flow | Adjusting controls or fixing the flow |
Boiler pressure too high or too low
Many residential boilers read roughly 12 to 15 psi when cold and a few psi higher when hot, though the right number depends on the boiler and the height of the house. A falling gauge usually means water is escaping somewhere, while a climbing one points to the expansion tank or the fill valve.
Residential boilers are often fitted with a relief valve rated at about 30 psi. If it drips or discharges, it’s doing its job: switch the boiler off, call, and never cap or plug it. Low boiler pressure is common after bleeding radiators, but a gauge that keeps dropping means a leak that refilling only hides.
Combi boiler repair: no hot water, or hot water but no heat
A combi boiler heats the house and the tap water from one wall-hung unit, so when one job fails and the other still works, the fault usually sits in the parts that switch between them: the diverter valve, a flow sensor, the plate heat exchanger or the system pressure. These are routine repairs for a gas technician.
- Hot water but no heat: often a stuck diverter valve or low pressure
- Heat but no hot water: often the diverter valve, a flow sensor or scale
- A lockout every time a tap opens: ignition, flame sensing or gas supply
Hard water is common in the GTA, so scale in a combi’s plate heat exchanger is a frequent cause. Weighing a new combi against a separate hot water tank? We can price both.
In-floor radiant heat and hydronic heating repair
Hydronic heating moves hot water from a boiler through radiators, baseboard convectors or tubing in the floor. Radiant floor heating runs at much lower water temperatures than radiators, which suits a condensing boiler, since it runs most efficiently when the returning water is cool.
We service manifolds, mixing valves, zone pumps, actuators and thermostats in Toronto basements, additions and renovated kitchens. A cold patch of floor usually means air in a loop, a failed pump or actuator, or a mixing valve set too low, so we start at the manifold.
Boiler repair in Toronto: what happens on a visit
Every boiler repair visit follows the same steps: a two-hour arrival window, a text when the technician is on the way, a full diagnosis and a flat-rate price. Nothing is repaired until you approve it, and most repairs are done that visit when the part is on the truck.
- Tell us what’s happening, including noises, the pressure reading and any fault code
- A real person calls back and books your arrival window
- The technician checks pressure, pumps, zone valves, the expansion tank, ignition, controls and venting
- You approve a flat-rate price, then we repair, bleed and balance the system
- Every repair comes with our written workmanship warranty
Emergency boiler repair in Toronto: what to do first
In a boiler emergency, safety comes first, then heat. We’re open 24/7, technicians go out day or night, weekends included, and emergency calls go to the front of the line. Before you call us, deal with anything that puts people at risk.
Gas smell, CO alarm or a discharging relief valve
If you smell gas, leave without touching switches, phones or flames, and call Enbridge Gas at 1-866-763-5427 from outside. If a CO alarm sounds, get everyone outside, call 911 and stay out until responders say it’s safe. If the relief valve is discharging, switch the boiler off.
Keeping the house and pipes safe while you wait
With no heat in a Toronto cold snap, the plumbing is at risk too. The City of Toronto advises opening kitchen, bathroom and laundry cabinet doors so warm air reaches the pipes, keeping areas with water pipes above 8°C, and knowing where your main water shut-off is. Never use a stove or oven to heat the house.
Boiler safety: carbon monoxide alarms and TSSA
A gas boiler is safe when it burns cleanly, vents properly and its safety devices work. Ontario’s Fire Code requires a CO alarm next to every sleeping area and, since January 1, 2026, on every storey of any home with a fuel-burning appliance such as a gas boiler, a fireplace or an attached garage.
The province’s carbon monoxide safety page (opens in a new tab) explains the rule. Gas work in Ontario is regulated by the TSSA (opens in a new tab), and all our gas work is done by TSSA-certified gas technicians, who check combustion, venting and the relief valve on each visit.
Should you repair or replace your boiler?
Repair makes sense when the boiler is sound and the fault is a pump, valve or control. Boiler replacement makes sense when the heat exchanger leaks, parts are no longer made, or an older low-efficiency boiler needs a major repair. We show you both prices side by side and say which we’d choose.
| Situation | Repair | Replace |
|---|---|---|
| Failed pump, zone valve, expansion tank or igniter | Yes, these are routine parts | Rarely |
| Leaking heat exchanger or cracked section | Rarely | Yes, in most cases |
| Parts no longer made for the model | Sometimes, if a substitute fits | Often |
| Old, low-efficiency boiler needing a major repair | Sometimes | Often, since a 90%+ AFUE condensing boiler cuts gas use |
| You also need a new water heater | Possible | Worth pricing a combi boiler |
Condensing boilers work with existing radiators in most Toronto homes, so a replacement rarely means opening walls. When replacing is the better call, our page on boiler installation in Toronto covers sizing, venting and installation day.
What affects the cost of boiler repair in Toronto?
The cost of boiler repair in Toronto depends on the part that failed, the boiler type, how easy the parts are to get, and whether the system needs flushing afterwards. We tell you the diagnostic fee on the phone, then give you a flat-rate price before any work starts.
| Factor | Why it matters |
|---|---|
| The failed part | A zone valve actuator is a far smaller job than a heat exchanger |
| Boiler type | Combi, condensing and cast iron boilers use different parts |
| Parts availability | Discontinued models may need parts ordered |
| System condition | Sludge, air or leaks may need flushing or extra repairs |
| Access | A cramped Toronto basement or a boxed-in boiler adds time |
The price you approve is the price you pay. It doesn’t change halfway through.
Annual boiler service and maintenance
A yearly boiler service before Toronto’s heating season cleans the heat exchanger and burner, checks combustion, tests the relief valve and expansion tank, and confirms the venting is safe. It catches worn parts before they fail on the coldest night and keeps a condensing boiler running efficiently.
- Condensate trap, drain and neutralizer cleared on condensing boilers
- Circulator pumps, zone valves and controls tested
- Radiators bled where needed, and a combi descaled if scale has built up
Our maintenance plan builds that yearly check into your schedule, with priority booking when it’s busy. Many manufacturer warranties ask for proof of regular maintenance.
Boiler repair across Toronto’s neighbourhoods
We handle boiler repair Toronto-wide, wherever a boiler heats the home: Victorian and Edwardian houses in Cabbagetown, Riverdale, High Park and Roncesvalles, larger renovated homes in Leaside and Forest Hill, and semis and row houses where the boiler shares one tight basement room with the water heater and laundry.
In Toronto’s century homes the work is usually old piping and seized radiator valves. Condo suites usually run on fan coils or in-suite heat pumps under building rules, so in a Toronto condo, start with property management.
Boilers and radiant heat questions
Why are my radiators cold at the top?
Cold tops usually mean trapped air. With the system off and cool, open the bleed screw with a radiator key, hold a cloth underneath, and close it as soon as water appears. Then check the gauge, since bleeding lowers the pressure. Constant bleeding points to a small leak.
What pressure should my boiler be at?
Many residential boilers read roughly 12 to 15 psi when cold and a few psi higher when hot, but check your manual or label for yours. A gauge that keeps falling suggests a leak. One that climbs toward the red points to the expansion tank or fill valve.
Why does my combi boiler give hot water but no heat?
The usual causes are a stuck diverter valve, which keeps sending heat to the taps instead of the radiators, low system pressure, a thermostat fault or a failed pump. Check the thermostat is calling for heat and note the pressure. If both look right, call a gas technician.
Do you offer emergency boiler repair in Toronto?
Yes. We’re open 24/7, and technicians go out day or night, weekends included, for no-heat and no-hot-water emergencies, which go to the front of the line. If you smell gas, leave and call Enbridge Gas from outside. If a CO alarm sounds, get everyone out and call 911.
How much does boiler repair cost in Toronto?
It depends on the part, the boiler type and the system’s condition. There’s a flat diagnostic fee, and we tell you the amount on the phone before booking. Then you get a flat-rate repair price, and nothing happens until you approve it.
How long does a boiler last, and when should I replace it?
Boiler makers put the average life of many boilers at around 15 years, and well-kept cast iron boilers often run far longer, so age alone isn’t the test. Replace when the heat exchanger leaks, parts are no longer made or repairs keep coming.
Can I fix my boiler myself?
Only the safe basics: check the thermostat, reset a tripped breaker once, read the pressure gauge, bleed a radiator with the system off and cool, and clear snow from vent pipes by hand. Don’t open sealed compartments, reset safety controls or touch the gas valve; that’s TSSA-certified work.
Which boiler brands do you repair?
We service all major brands, including combi boilers, condensing boilers, older cast iron boilers and the pumps, zone valves and controls around them. Tell us the make, the model and any fault code when you book, so the technician can bring likely parts.
Need boilers and radiant heat service? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
