Skip to content
Gas furnace and water heater in a home basement
Repair, replacement, tune-ups

Furnace repair in Toronto and the GTA

(647) 692-0819Open 24/7, day or night

Assurance HVAC Heating & Cooling handles furnace repair in Toronto and across the GTA, from a failed ignitor on a January night to a blower motor that squeals every time the heat comes on. Our TSSA-certified gas technicians find the real fault, give you a flat-rate price before any work starts, and back every repair with a written workmanship warranty. We fix every major brand, standard and high-efficiency, in homes across Toronto and six more GTA cities.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Furnace repair in Toronto and six more GTA cities, on every major furnace brand.
  • All gas work done by TSSA-certified gas technicians, WSIB covered and fully insured.
  • A flat-rate price after diagnosis, approved by you before any work starts.
  • Open 24/7 for no heat, with technicians out day or night. Booked visits get a two-hour arrival window.
  • A written workmanship warranty on every repair. Book online or call to get started.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Signs you need furnace repair in Toronto
  2. Furnace not working? Try these troubleshooting steps first
  3. No heat after hours? Call any time
  4. Furnace repair by symptom: what’s likely wrong
  5. Furnace parts we repair and replace
  6. High-efficiency furnace repair: condensate, venting and error codes
  7. Furnace repair in Toronto: what happens on a visit
  8. How long does a furnace repair take?
  9. How much does furnace repair cost in Toronto?
  10. When repair stops making sense
  11. If it’s time for a new furnace
  12. Keeping the furnace from breaking down
  13. Cold rooms, dry air and other comfort problems
  14. Furnace repair in Toronto homes, old and new
  15. Furnace brands we service
  16. Furnaces questions

Signs you need furnace repair in Toronto

Call for furnace repair when the house won’t warm up, the furnace starts and stops every few minutes, or it makes new noises. Most furnaces give warning signs before they fail, and catching them early in a Toronto winter usually means a smaller repair and less time without heat.

  • No heat, or the blower runs but the air is cold
  • Short cycling, on and off every few minutes
  • Banging, squealing or a loud boom when the burners light
  • Some rooms much colder than others
  • Gas bills rising while your usage hasn’t changed
  • A yellow, flickering flame instead of a steady blue one

Furnace not working? Try these troubleshooting steps first

If your furnace is not working, a few quick checks can save a service call. Run through these checks before you book, and if the heat still doesn’t come back, call us.

  • Thermostat set to heat, a few degrees above room temperature, with fresh batteries
  • Furnace power switch and breaker on, and the blower door closed tight
  • A clean filter, since a clogged one can overheat the furnace and shut it down
  • On a high-efficiency furnace, vent pipes clear of snow and ice and the condensate pump plugged in
  • Any blinking error code on the control board written down before you cut the power

No heat after hours? Call any time

We’re open 24/7 for no-heat emergencies in Toronto and across the GTA, with technicians out day or night, weekends included, and emergency calls go to the front of the line. Our emergency furnace repair page covers what to check while you wait. If you smell gas, leave the house without touching switches or flames and call Enbridge Gas at 1-866-763-5427 from outside. If a carbon monoxide alarm sounds, get everyone outside and call 911.

Furnace repair by symptom: what’s likely wrong

Most furnace problems show up as one of a handful of symptoms, and each points to a short list of likely causes. Mention the symptom and any error code when you book. A clogged filter or a blocked condensate line causes a surprising share of no-heat calls on its own.

Furnace symptoms, likely causes and typical repairs
SymptomLikely causeTypical repair
No heat, nothing happensNo power, a tripped safety switch, or a failed ignitor or boardRestore power, replace the failed part
Blower runs, air is coldBurners not lighting, fan set to On, or a tripped limit switchTest ignition and airflow, replace the failed part
Burners light, then shut offDirty or worn flame sensorClean or replace the flame sensor
Short cyclingClogged filter, overheating or an oversized furnaceReplace the filter, check airflow and temperature rise
Pressure switch error codeBlocked vent or condensate trap, or a weak inducerClear the vent and trap, replace the switch or inducer
Humming, squealing or grindingWeak capacitor, or worn blower or inducer motor bearingsReplace the capacitor or motor
Loud boom at ignitionDelayed ignition from dirty burners or low gas pressureClean the burners, set the gas pressure
Water around the furnaceBlocked condensate line, trap or drain pumpClear the line and trap, replace a failed pump

Furnace parts we repair and replace

Most furnace repairs in Toronto come down to one of a short list of furnace parts. We test each one in the order the furnace uses it, so we replace the part that actually failed instead of guessing.

  • Hot surface ignitor: lights the burners, and cracks or burns out with age
  • Flame sensor: proves the burners lit; a coated one shuts the furnace off within seconds
  • Inducer motor: pulls combustion gases out the vent; worn bearings hum or squeal
  • Pressure switch: confirms a safe draft before ignition
  • Limit switch: shuts the burners off when the furnace overheats
  • Control board: runs the heating sequence and flashes the error codes
  • Blower motor and capacitor: a weak capacitor makes the blower hum or fail to start
  • ECM blower motor: its electronic module can fail and sometimes be replaced alone
  • Gas valve: feeds the burners; we test gas pressure and the valve’s signal first

A cracked heat exchanger is the exception. It can leak carbon monoxide into your home’s air, so the furnace has to stay off, and it usually means replacement. Ontario’s Fire Code requires a CO alarm next to every sleeping area and, since January 1, 2026, on every storey of any home with a fuel-burning appliance, a fireplace or an attached garage, and the province’s carbon monoxide safety page (opens in a new tab) explains the rules.

High-efficiency furnace repair: condensate, venting and error codes

High-efficiency furnace repair often comes down to water and air. A condensing furnace pulls so much heat from its exhaust that water forms inside it, and when that condensate or the plastic venting backs up, the pressure switch shuts the furnace down.

Condensate trap, drain and pump

Condensate flows through a trap to a floor drain or a small pump. Sludge in the trap, a kinked line or a failed pump can trip the pressure switch or leak water, so we clean the trap, clear the line or replace the pump.

PVC intake and exhaust pipes

Most high-efficiency furnaces in Toronto vent through plastic pipes, usually two, out a side wall. Drifting snow, ice or a sagging pipe that holds water can set off pressure switch errors, so we clear the pipes and check their slope.

Error codes and the blinking LED

A small LED on the control board blinks a code when something goes wrong, with the code chart usually inside the furnace door. Write the pattern down before cutting the power, since a power cycle can clear it.

Furnace repair in Toronto: what happens on a visit

Every furnace repair visit follows the same steps. We confirm a two-hour arrival window, text you when the technician is on the way, find the actual fault and give you a flat-rate price. Nothing gets fixed until you approve that price.

  • Book online or by phone with the symptoms, any error codes and the furnace’s age.
  • A real person calls back to confirm your arrival window.
  • We test the ignitor, flame sensor, pressure switches, gas valve, control board and blower.
  • You approve a flat-rate price, with the replacement price beside it on older furnaces.
  • We make the repair, then run a full heating cycle and check the safety controls.

Gas work in Ontario is overseen by the TSSA (opens in a new tab), and every gas furnace repair we do is handled by a TSSA-certified gas technician.

How long does a furnace repair take?

Most furnace repairs are finished in a single visit when the part is on the truck. A single-part fix like a flame sensor, ignitor or capacitor is a short job, while motors, control boards and gas valves take longer. A part that has to be ordered means a second trip, and we tell you before you approve the repair.

  • Short jobs: cleaning a flame sensor, or replacing a filter, ignitor, capacitor or pressure switch
  • Longer jobs: inducer and blower motors, ECM modules, control boards, and gas valves with a pressure and leak test

How much does furnace repair cost in Toronto?

Furnace repair cost in Toronto depends on the part that failed, the furnace’s make and age, access to the unit and whether the part is on the truck. There’s a flat diagnostic fee, which we tell you before booking, then a flat-rate repair price you approve before any work starts.

What affects the cost of furnace repair
FactorWhy it matters
The part that failedCleaning a flame sensor is a small job. A control board, ECM motor or gas valve costs more.
Make and modelSome brands use model-specific parts, and parts for older furnaces can be harder to find.
AccessTight furnace rooms and finished basements add labour time.

Whatever the job, the price you approve doesn’t change halfway through.

When repair stops making sense

Repair usually makes sense when the furnace is under about 15 years old and one part like an ignitor or flame sensor has failed. Replacement starts to make sense at 15 to 20 years, when a major part such as the heat exchanger or control board fails or repairs come every winter.

Repairing versus replacing a gas furnace
SituationRepair usually makes senseReplacement usually makes sense
AgeUnder about 15 years15 to 20 years or older
Type of failureIgnitor, flame sensor or pressure switchCracked heat exchanger, or a major part on an older unit
Repair historyFirst problem in yearsRepeat repairs every winter

We give you both prices side by side and tell you which we’d choose for our own home. If replacement comes out ahead, see the next section.

If it’s time for a new furnace

A new furnace should be sized with a heat-loss calculation, not copied from the old nameplate, and a high-efficiency condensing model is rated 90% AFUE or higher. Our furnace installation page covers sizing, AFUE and two-stage or modulating choices, and the full repair-or-replace comparison, and we handle the permits and inspections the job needs. If your central air is the same age, price a cold-climate heat pump at the same time.

Keeping the furnace from breaking down

Many repairs on this page start as wear a yearly check would catch, like a coated flame sensor, a worn ignitor or a condensate trap starting to clog. A fall furnace maintenance visit cleans the burners, inspects the heat exchanger and tests the safety controls before the cold arrives. Our maintenance plan covers two tune-ups a year with priority booking, and many manufacturer warranties ask for proof of regular maintenance, so check your warranty papers.

Cold rooms, dry air and other comfort problems

Cold rooms and dry winter air aren’t always a furnace fault. In many Toronto homes the problem is airflow, ductwork or humidity, so we check airflow before recommending a bigger furnace, which can make uneven heat worse.

Fixes include balancing dampers, sealing duct joints, adding a return or zoning a finished third floor. For static shocks and dry skin, a furnace-mounted humidifier from our indoor air quality service keeps winter humidity in a healthy range.

Furnace repair in Toronto homes, old and new

Furnace repair in Toronto looks different from one street to the next. A century semi in Leslieville or Riverdale might squeeze the furnace, water heater and laundry into one tight basement room, while a bungalow in Etobicoke or Scarborough may still run on its original ductwork.

Across the GTA, many homes in Richmond Hill, Markham and Vaughan still run builder-installed furnaces from the 1980s to the 2000s, now at the age when ignitors, inducers and control boards wear out. We repair furnaces in houses, townhouses and low-rise condos in all 12 areas we serve across the GTA.

Furnace brands we service

We service and repair every major furnace brand found in Toronto homes, including Lennox, Carrier, Trane, Goodman, Rheem, Bryant, Amana, Daikin, York and Napoleon. A builder-grade furnace in a newer subdivision gets the same careful diagnosis and flat-rate price as a premium modulating model.

FAQ

Furnaces questions

Why does my furnace keep turning on and off?

That’s called short cycling. Common causes are a clogged filter, a dirty flame sensor, overheating from poor airflow, a badly placed thermostat or a furnace that’s too big for the house. Change the filter first. If it keeps happening, book a visit, because short cycling wears parts out quickly.

Why is my furnace blowing cold air?

Check the thermostat first. If the fan is set to On instead of Auto, the blower runs between heating cycles and the air feels cool. If it’s on Auto and the air stays cold, the burners aren’t lighting or staying lit, often from a failed ignitor, a dirty flame sensor or a clogged filter that overheats the furnace.

Is it safe to reset a furnace?

Once, yes. Turning the furnace off at its power switch for a minute and back on clears a temporary lockout. If it locks out again, stop there, because the control board is shutting it down for a reason, like a failed ignitor, a dirty flame sensor or a blocked vent. If you smell gas, don’t reset anything: leave the house without touching switches or flames and call Enbridge Gas from outside.

Can a flame sensor be cleaned instead of replaced?

Usually, yes. The flame sensor is a thin metal rod that proves the burners are lit, and a coating builds up on it over time. A technician cleans it with a fine abrasive pad, which often fixes a furnace that lights and then shuts off. If the rod is worn or the porcelain is cracked, we replace it.

Is it safe to run a furnace with a cracked heat exchanger?

No. A cracked heat exchanger can let carbon monoxide into the air your furnace moves through the house. If a technician finds one, the furnace should stay off until it’s repaired or replaced. Keep your carbon monoxide alarms working, and if one goes off, get everyone outside and call 911.

Do you work on all furnace brands?

Yes. We service and repair Lennox, Carrier, Trane, Goodman, Rheem, Bryant, Amana, Daikin, York, Napoleon and the other brands found in Toronto homes. Common parts ride on the truck, and if a part has to be ordered, we tell you before you approve the repair.

What does a furnace service call cost in Toronto?

There’s a flat diagnostic fee, and we tell you the amount on the phone before we book. After the diagnosis, you get a flat-rate price for the repair, and nothing happens until you approve it. That price doesn’t change halfway through the job.

Which parts of the GTA do you cover for furnace repair?

We repair furnaces across 12 GTA areas. Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville each have a local office and phone line, and Brampton, Pickering, Ajax, Aurora and Newmarket are served from the main line. Booked visits get a two-hour arrival window and a text. No-heat calls go to the front of the line, with technicians out day or night, 24/7.

Book a visit

Need furnaces service? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy