Skip to content
Hand adjusting a smart thermostat on a wall
Homeowner guides

Furnace not turning on: causes and fixes

(647) 692-0819Open 24/7, day or night

A furnace not turning on in a Toronto winter feels urgent, but the cause is often something you can check yourself in a few minutes. This guide covers the safe checks, what the furnace’s sounds tell you, which parts usually fail and when to stop and call. If the heat still won’t come back, we handle furnace repair in Toronto and across the GTA, 24/7.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Start with the thermostat, the furnace service switch, the breaker and the filter.
  • On high-efficiency furnaces, clear snow and ice from the outdoor plastic pipes by hand.
  • Try one reset only. A repeat lockout means a safety control is doing its job.
  • Gas smell: leave, then call Enbridge Gas from outside. CO alarm: everyone out, call 911.
  • We’re open 24/7, and you approve a flat-rate price before any repair begins.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Why is my furnace not turning on?
  2. Check the thermostat first
  3. Make sure the furnace has power
  4. A clogged filter can shut the furnace down
  5. Snow, ice or frost on the outdoor vent pipes
  6. How to reset a furnace that won’t turn on
  7. Furnace not turning on after a reset? Leave it off
  8. Parts that stop a furnace from starting
  9. Furnace not turning on in a cold snap or after an outage
  10. When it’s a safety call, not a repair
  11. What happens when you call us
  12. Repair, replace, or prevent the next one
  13. Furnace not turning on: common questions

Why is my furnace not turning on?

Most no-start problems come down to four things: a thermostat that isn’t calling for heat, a furnace with no power, a safety switch tripped by overheating or blocked venting, or a worn ignition part. You can often sort out the first three yourself. The last one needs a licensed gas technician.

What a furnace that won’t start usually means, and who fixes it
What you noticeLikely causeWho fixes it
Blank thermostat screenDead batteries, or a smart thermostat that lost its power from the furnaceYou (batteries), then a technician
Thermostat on, furnace silentService switch off, a tripped breaker or a blown control board fuseYou (switch and breaker), a technician (fuse)
Stopped right after a filter changeFurnace door not fully closed, so its safety switch cuts the powerYou
Small motor runs, no flameSnow on a vent pipe, a blocked condensate drain or a pressure switch faultYou (snow), a technician (the rest)
Orange glow but no flame, or a flame that drops outGas supply, gas valve, ignitor or a coated flame sensorTechnician
Ran fine, now overheats and stopsClogged filter or closed registersYou, then a technician if it repeats

If the blower runs but the vents feel cold, that’s a different problem, covered in our guide to a furnace blowing cold air.

Check the thermostat first

A wrong thermostat setting looks exactly like a broken furnace, so start there. Set it to Heat, not Cool or Off, and raise the setpoint a few degrees above the room temperature. Then give the furnace a few minutes to respond before you check anything else.

  • Replace the batteries if the screen is blank, dim or flashing a warning.
  • Look for a schedule, hold, away or eco setting that is keeping the temperature down.
  • Many smart thermostats draw power from the furnace, so a dark screen can mean the furnace has lost power.
  • Don’t pull the thermostat off the wall or handle its wires.

Make sure the furnace has power

A gas furnace still runs on electricity: the control board, ignitor, inducer and blower all need it. Two things cut that power without anyone noticing, the furnace service switch, which looks like an ordinary light switch, and the furnace breaker in your electrical panel.

  • The service switch sits on or near the furnace and gets flipped off by mistake surprisingly often, especially beside a basement light switch.
  • If the furnace breaker has tripped, push it fully off and back on once. If it trips again, leave it off and call, since that points to an electrical fault.

A clogged filter can shut the furnace down

A clogged filter starves the furnace of air, the heat exchanger runs too hot, and the high-limit switch cuts the burners to protect it. After enough of those trips, some control boards lock the furnace out completely, so a dirty filter can end in no heat at all.

  • Hold the filter up to a light. If no light passes through, replace it, with the arrow pointing toward the furnace.
  • If the filter sits behind the lower furnace door, push the door fully closed afterward, because a door switch keeps the furnace off while it’s loose.
  • Open the supply registers and keep furniture and rugs off the return grilles.

Snow, ice or frost on the outdoor vent pipes

High-efficiency furnaces breathe through two plastic pipes, usually white PVC, that exit a side wall or the roof. When snow, ice or frost blocks either one, a pressure switch senses the poor draft and won’t let the burners light. After a Toronto snowstorm or a deep freeze, check these early.

  • Clear snow, ice or frost from the pipe openings by hand or with a soft brush. Don’t chip at them with a tool or bend the pipes.
  • Keep shovelled and plowed snow away from that wall. If the pipes exit through the roof, don’t climb up; call us.

Pipes that ice up again and again may need their slope or termination corrected, as our guide to a frozen furnace vent pipe explains.

How to reset a furnace that won’t turn on

Once the thermostat, power, filter and vent pipes check out, one reset is safe and clears a temporary lockout. Turn the furnace off at its service switch, wait about 30 seconds, and switch it back on. Leave the thermostat calling for heat and listen to what happens next.

  • Write down any blinking status light pattern first, since cutting the power can erase it.
  • Don’t press buttons on the control board or reset any switch inside the cabinet.
  • Don’t relight anything. Modern furnaces light themselves, and an older furnace whose pilot has gone out needs a technician.

Furnace not turning on after a reset? Leave it off

A furnace not turning on after one reset has usually locked out on purpose, because a safety control saw poor venting, overheating or a flame that wouldn’t prove. Resetting it again and again only makes it retry under the same conditions. Switch it off, set the thermostat to Off and call.

It helps to tell us where the start-up stopped. From a few steps away, a normal start sounds like this:

  • A click as the thermostat calls for heat, then the steady whir of the inducer motor
  • Another click as the pressure switch confirms the draft
  • An orange glow from the ignitor, then a soft whoosh as the burners light
  • Burners that stay lit, and the blower starting after a short delay

Silence after the inducer points to venting, condensate or the pressure switch. A glow with no flame points to the gas supply, gas valve or ignitor. A flame that drops within seconds usually means the flame sensor.

Parts that stop a furnace from starting

When the simple checks pass, the cause is usually one worn part in the ignition chain. These are technician jobs because they involve gas, line voltage and combustion safety, and a failed part often has a cause behind it. We test each part rather than swapping them until something works.

  • Hot surface ignitor: a ceramic element that turns brittle with age and can crack without looking damaged.
  • Flame sensor: a metal rod that proves the flame. A coated one lets the burners light, then shuts them down.
  • Pressure switch and inducer: a weak inducer, a cracked hose or a blocked condensate trap keeps the switch from closing.
  • Control board and limit switches: a short can blow the board’s fuse, and limit or rollout switches open when something overheats.

Furnace not turning on in a cold snap or after an outage

A furnace not turning on during a GTA cold snap often has a winter cause. Long, back-to-back cycles expose a weak ignitor or inducer, drifting snow buries side-wall vents, and condensate lines along an outside wall or through a cold garage can freeze.

  • After an outage, most furnaces restart on their own. If yours doesn’t, check the breaker and try the one reset; a power surge can occasionally damage a control board.
  • Water near a high-efficiency furnace, or gurgling in a deep freeze, can mean a frozen condensate drain. Leave the drain and trap to the technician.
  • While you wait, open the cabinets under sinks on outside walls so those pipes get some warmth.

When it’s a safety call, not a repair

A smell of gas, a carbon monoxide alarm, smoke or a burning electrical smell turns a no-heat problem into a safety call. Stop troubleshooting, don’t reset the furnace or flip switches to test it, and deal with the danger before anything else.

  • Gas smell, like rotten eggs: leave the home right away. Don’t touch light switches, light a match or lighter, or use your phone until you’re outside, then call Enbridge Gas at 1-866-763-5427.
  • Carbon monoxide alarm: get everyone outside, pets included, and call 911. Don’t go back in to check the furnace.

Enbridge publishes natural gas safety advice (opens in a new tab). Ontario requires CO alarms next to every sleeping area and, since January 1, 2026, on every storey of a home with a fuel-burning appliance, a fireplace or an attached garage, as its carbon monoxide safety page (opens in a new tab) explains.

What happens when you call us

We’re open 24/7, with technicians going out day or night, and homes with no heat go to the front of the line. A TSSA-certified gas technician with a G2 or G1 certificate finds the fault and gives you a flat-rate price to approve before any repair.

  • Nights and weekends: call our emergency furnace repair line at any hour.
  • Booked visits get a two-hour arrival window and a text when the technician is on the way.
  • A written workmanship warranty on every repair, on all major brands, in all 12 areas on our service area page.

Repair, replace, or prevent the next one

A failed sensor, ignitor or switch is usually worth repairing. If the furnace is around 15 to 20 years old and the problem is the heat exchanger, the control board or a string of breakdowns, compare repair against replacement before you spend. Regular service catches most worn parts early.

Our guide on whether to repair or replace a furnace covers that decision, and our HVAC maintenance plan includes two tune-ups a year to catch ageing ignitors, coated flame sensors and clogging condensate traps before winter.

FAQ

Furnace not turning on: common questions

Is a furnace not turning on an emergency?

It is when the house has no heat in freezing weather, someone at home is vulnerable to the cold, or you notice gas, a CO alarm or a burning smell. We’re open 24/7, and no-heat calls go to the front of the line. If the house is holding its temperature, a booked visit is usually fine.

Why does my furnace click but not start?

A click usually means a relay on the control board heard the thermostat, so the signal is arriving. If nothing follows, or the inducer runs and then stops, the start-up is failing a safety check, often at the pressure switch, ignitor or gas valve. Try one reset, and if it quits again, call.

Why won’t my furnace start after a power outage?

Most furnaces restart when power returns, but some end up in a lockout, and a surge can occasionally damage the control board. Check the breaker and that the thermostat came back on Heat, then do one reset at the service switch. If it still won’t start, the board or ignitor needs testing.

Can a dirty filter stop a furnace from turning on?

Yes, indirectly. A clogged filter makes the furnace overheat, the high-limit switch shuts the burners off, and repeated trips can make the control board lock the furnace out. Replace the filter, open the registers and try one reset. If it keeps overheating with a clean filter, call a technician.

My thermostat screen is blank. Is the furnace broken?

Not necessarily. Try fresh batteries first. If the thermostat has no batteries and runs on power from the furnace, as many smart thermostats do, a blank screen means the furnace has no power. Check the service switch and the breaker. If both are on, a blown fuse on the control board is a likely cause.

How long should I wait after a reset before calling?

Give it a few minutes. The furnace runs its inducer for a short purge, warms the ignitor, lights the burners and then starts the blower after a delay. If several minutes pass with no warm air, or it starts and shuts off again, leave it off and call us.

Can I use a space heater while I wait for a technician?

Yes, with care. Use an electric heater with tip-over shut-off, keep it well clear of curtains and bedding, plug it straight into a wall outlet and turn it off when you go to sleep. Never warm the house with a gas stove, barbecue, propane heater or generator, since they can produce carbon monoxide.

Which areas do you cover for no-heat calls?

We take no-heat calls in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville, on every major furnace brand. Each area has its own page and local phone line, a TSSA-certified gas technician handles every call, and you approve a flat-rate price before any work begins.

Book a visit

Still no heat? We’ll call you back to book a technician.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy