
Furnace repair in Markham, all major brands
(647) 496-5598Open 24/7, day or night
Assurance HVAC Heating & Cooling of Markham provides furnace repair in Markham for the original builder-grade furnaces still running in many 1990s and 2000s subdivisions, the condensing furnaces in newer homes and the units squeezed into tight basements in Unionville and Markham Village. A TSSA-certified gas technician finds the part that actually failed, and you approve a flat-rate price before any part is swapped. See our HVAC contractor in Markham page for our other services.
Key takeaways
- Furnace repairs across the city, from Thornhill and Milliken to Cornell, Cathedraltown and Box Grove.
- Gas work by TSSA-certified G2 and G1 technicians, covered by WSIB and fully insured.
- A flat diagnostic fee quoted on the phone, then a repair price you approve first.
- Booked visits come with a two-hour arrival window and a text; no-heat calls go first.
- Every repair is backed by a written workmanship warranty.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Markham service team.
On this page
- How a Markham furnace tells you it needs repair
- Why the age of your Markham home shapes the repair
- Furnace troubleshooting to try before you book
- Furnace not working? The repairs we make most in Markham
- Furnace blowing cold air in a Markham home?
- High-efficiency furnace repair in newer Markham homes
- What happens during furnace repair in Markham
- Pricing furnace repair in Markham, from Cornell closets to Unionville basements
- Repair or replace an original builder-grade furnace?
- Gas furnace repair and safety: gas smells and CO alarms
- Brands found in Markham basements and closets
- Preventing the next furnace repair in Markham
- Furnace repair in Markham and nearby areas
- Furnace repair questions from Markham homeowners
How a Markham furnace tells you it needs repair
Most furnaces give some warning before they quit. The early signs are usually a furnace that lights and then drops out, a blower that hums before it starts, short bursts of heat with long gaps between them, or a second floor that falls further behind the main floor every cold night.
- The burners light, then shut off within seconds, again and again
- A whine, rattle or hum from the cabinet that wasn’t there last winter
- A blinking light on the control board, visible through the blower door
- Water on the floor beside a high-efficiency furnace
Why the age of your Markham home shapes the repair
The faults we find follow the age of the house. Many 1990s and 2000s subdivisions still run original builder-grade furnaces, older Milliken and Thornhill streets pair a replacement furnace with decades-old ducts, and heritage homes in Unionville and Markham Village bring cramped basements and sometimes chimney venting.
Builder-grade furnaces in Berczy Village, Cachet and Angus Glen
After 20 years or so, igniters crack, inducer bearings whine and control boards fail. In the larger two-storey homes there, one furnace also heats a finished basement, which works the blower hard.
Milliken and Thornhill: a newer furnace on older ducts
Many houses here went up between the 1960s and the 80s and are on their second furnace, still connected to ducts with few upstairs returns. Restricted airflow trips the limit switch, so the lasting fix may be a duct change.
Heritage homes in Unionville and Markham Village
Older homes can tuck the furnace into a low corner with little room to work, and some still vent through a chimney. We check the draft on every repair in these houses, because a poor draft trips the safety controls.
Furnace troubleshooting to try before you book
A few minutes of furnace troubleshooting can save a service call. Some no-heat calls in Markham turn out to be a thermostat setting, a tripped breaker, a service switch bumped off or a filter packed with renovation dust, and you can check each of those yourself.
- Thermostat set to Heat, a couple of degrees above the room, with fresh batteries
- The furnace service switch, which looks like a light switch, and its breaker both on
- A clean filter, because a clogged one can trip the limit switch
- On a high-efficiency furnace, an unkinked drain hose and a plugged-in condensate pump
- The plastic vent pipes outside, usually two on a side wall, clear of snow, leaves or nests
If the control board light is blinking, write the pattern down before cutting the power, since a reset clears the code. Reset it once at most, and if it locks out again, leave it off and book a repair.
Furnace not working? The repairs we make most in Markham
When a furnace is not working, the cause is nearly always one of a dozen or so parts, tested in the order the furnace uses them. These are the ones we fix most often across the city, old furnaces and new.
| Part | What you notice | Usual repair |
|---|---|---|
| Flame sensor | Burners light, then go out within seconds | Clean the rod, or replace it if worn |
| Hot surface igniter | Inducer starts, no flame, then a lockout | Replace the igniter |
| Inducer motor | Whining at start-up, or no draft | Replace the inducer assembly |
| Pressure switch | Inducer runs, burners never fire, a code flashes | Clear the hose or vent, or replace the switch |
| Limit switch | Short bursts of heat, blower still running | Fix the airflow fault, then test the switch |
| Blower motor or ECM module | A hum with little airflow, or the wrong speed | Replace the capacitor, module or motor |
| Control board | The thermostat calls for heat and nothing happens | Check its inputs, then replace the board |
Common furnace parts ride on the truck. Some brand-specific boards and motors have to be ordered, and you’ll know before you approve anything.
Furnace blowing cold air in a Markham home?
A furnace blowing cold air usually has the fan running with no flame behind it. First check that the thermostat fan is set to Auto rather than On. If it is, the burners are failing to light or stay lit, which points to the igniter, the flame sensor, a pressure switch or a tripped limit switch.
In two-storey Markham homes with finished basements, the complaint is often cool air from the bedroom registers only. That’s usually airflow: a dirty filter, a closed damper, a slow blower setting or too few upstairs returns.
High-efficiency furnace repair in newer Markham homes
High-efficiency furnace repair is mostly about water and air. Condensing furnaces, rated 90% AFUE or higher, are what you’ll usually find in newer homes in Cathedraltown, Wismer and Cornell, and they shut down when the condensate trap clogs, the drain line freezes or the plastic intake and exhaust pipes get blocked.
Condensate trap, drain and pump
In a finished basement the condensate pump often hides behind a panel, and when it fails the water ends up in the carpet. We clean the trap, flush the line and test or replace the pump.
Vent pipes on Cornell lots and townhome rows
In Cornell and on other compact lots, the pipes can end near a walkway or deck where snow piles up. We clear the ends, read the error code and check the pipes for sags that hold water.
What happens during furnace repair in Markham
Every visit for furnace repair in Markham follows the same routine. You book by phone or the request form, a real person calls back to confirm a two-hour arrival window, and a text tells you when the technician is on the way. The fault is found and priced before anything is touched.
- The technician checks ignition, the flame, the draft, gas pressure, the safety switches and the blower.
- You get a flat-rate repair price, with a replacement price beside it on an older furnace.
- Once you approve, we make the repair and run complete heating cycles before leaving.
Gas work in Ontario falls under the TSSA (opens in a new tab), and the technicians who handle our gas furnace repair hold G2 or G1 gas certificates.
Pricing furnace repair in Markham, from Cornell closets to Unionville basements
What you pay depends on which part failed, the make and age of the furnace, whether the part is on the truck and how easy the furnace is to reach. We don’t post prices, because two furnaces rarely fail the same way, but the repair price is fixed and agreed with you before any work starts.
| What we look at | Why it changes the price |
|---|---|
| The failed part | Cleaning a flame sensor is quick. A control board or ECM motor takes more parts and time. |
| Make and age | Builder-grade furnaces from the 1990s and early 2000s can need harder-to-find parts. |
| Access | A furnace boxed in by finished basement walls or set in a tight closet takes longer. |
| Related faults | A limit switch that tripped from poor airflow may need the airflow fixed as well. |
The diagnostic fee is flat and quoted before booking, and the approved repair price holds for the whole job.
Repair or replace an original builder-grade furnace?
Repair usually wins on a furnace younger than about 15 years with one failed wear part. Once it reaches 15 to 20 years, as many original furnaces in Markham’s 1990s and 2000s subdivisions have, a failed heat exchanger, control board or blower motor often tips the decision toward replacing it.
| Question | Points to repair | Points to replace |
|---|---|---|
| How old is the furnace? | Under about 15 years | 15 to 20 years or more |
| What failed? | A sensor, igniter or switch | The heat exchanger, or a board or motor on an old unit |
| How often has it broken down? | First repair in years | A repair most winters lately |
| Is the central air the same age? | The AC has good years left | Both are near the end |
You get both prices and our honest pick. If replacement wins, the furnace installation in Markham page walks through sizing with a heat-loss calculation.
Gas furnace repair and safety: gas smells and CO alarms
Some furnace problems are safety problems first. A gas smell, a carbon monoxide alarm, or headaches and nausea that ease once you step outside all mean the same thing: get everyone out of the house and call 911 if anyone feels unwell, before you think about the furnace.
- Smell gas: go outside without flipping switches, lighting a match or using your phone indoors, then call Enbridge Gas at 1-866-763-5427 from outside.
- Carbon monoxide alarm: get everyone, pets included, outside and call 911.
- Cracked heat exchanger: the furnace stays off, because the crack can let CO into the air your ducts carry.
Ontario requires CO alarms next to each sleeping area and, since January 1, 2026, on every storey of homes with a fuel-burning appliance, a fireplace or an attached garage, so test yours monthly. For a no-heat call on a night or weekend, see emergency furnace repair in Markham for what to do while you wait.
Brands found in Markham basements and closets
We repair all major brands found in Markham homes, from Goodman, Carrier and Lennox to Napoleon, Trane, York, Rheem, Daikin, Amana and Bryant, plus the builder-grade models in the city’s subdivisions. Each gets the same testing and flat-rate pricing, from a single-stage unit to a modulating furnace.
Preventing the next furnace repair in Markham
Many repairs start as slow wear a yearly visit would catch: a coated flame sensor, a condensate pump starting to fail behind a finished-basement panel, or a limit switch tripping because an older Thornhill home has too few returns. A fall tune-up finds those while the weather is still mild, well before the first hard freeze.
Our HVAC maintenance plan covers two tune-ups a year with priority booking. If the furnace is under a manufacturer warranty, read the terms, since many ask for service records.
Furnace repair in Markham and nearby areas
We handle furnace repair in Markham in every neighbourhood, from Buttonville and Unionville to Box Grove, Cornell and Greensborough, and on the Milliken and Thornhill streets close to Steeles. We also work in Richmond Hill, North York and Toronto, with the same licensed technicians and flat-rate pricing.
Furnace repair questions from Markham homeowners
The burners light and then cut out. What’s causing it?
Most often it’s a dirty flame sensor, the small metal rod that confirms the burners lit. Coated in residue, it can’t prove the flame, so the control board closes the gas valve for safety. A technician’s cleaning usually solves it. We also test the ground wire and gas pressure, which can cause the same cut-out.
Why does the upstairs of our Markham home stay cold when the furnace runs?
Usually it’s airflow, not a furnace fault. Warm air has a long way to travel to the bedrooms, and few upstairs returns, a dirty filter, a closed damper or a slow blower setting lose much of it on the way. We measure airflow, then adjust the blower, balance dampers or suggest a return. A bigger furnace rarely helps.
Why is there water on the floor next to our furnace?
On a high-efficiency furnace, water usually means the condensate system has backed up: a clogged trap, a kinked or frozen drain line, or a failed condensate pump. In a finished basement it can reach flooring and drywall quickly, so switch the furnace off, mop up and book a repair. A humidifier leak or AC coil drain can also be the source.
Why does our furnace bang when the burners light?
A bang at ignition is usually delayed ignition: gas builds up for a moment before it lights, often because the burners are dirty, the igniter is weak or the gas pressure is off. It stresses the heat exchanger every time, so switch the furnace off at its service switch and call us. If you ever smell gas, leave without touching switches or flames and call Enbridge Gas from outside.
Do you repair furnaces in older Unionville and Markham Village homes?
Yes. Heritage homes can have low basements, awkward access and furnaces that still vent through a chimney. On those visits we check the draft and the flue connection along with the repair, since poor venting can trip safety controls and is a carbon monoxide risk.
Can I get furnace repair in Thornhill, Cornell or Cathedraltown?
Use the local number shown on this page, or the request form. Our technicians cover the whole city, from Thornhill and Milliken near Steeles up to Cathedraltown, and from Unionville east to Box Grove and Cornell. You get a two-hour arrival window for booked repairs, and no-heat calls go to the front of the line, with a technician out day or night.
Is there a charge for the technician to diagnose the furnace?
Yes. The diagnostic fee is a flat amount we quote by phone before the visit is booked. Once the fault is found, the repair gets its own flat-rate price, and nothing happens without your approval. That price stays fixed for the job.
Can you still get parts for a 20-year-old builder-grade furnace?
Usually, yes. Igniters, flame sensors, capacitors and pressure switches are widely available, and the common ones ride on the truck. Control boards and blower motors for discontinued models can be harder to source, and sometimes a universal part is the answer. If a part is hard to get, we price a replacement alongside the repair.
Need furnace repair in Markham? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
