
When the furnace starts, hums and then never lights, the ignitor is one of the first suspects. A furnace ignitor not working is a very common reason for no heat, especially at the first cold snap of the year. This guide explains what the ignitor does, how to tell it from other faults, what you can safely check, and when to call for furnace repair.
Key takeaways
- The ignitor lights the gas, and a cracked or worn one is a common cause of no heat.
- A bad ignitor looks like a running inducer fan, no glow, no flame and then a lockout.
- Other faults mimic it, so a technician tests the ignitor before replacing anything.
- Replacing it means opening the sealed burner area, which is gas work for a licensed technician.
- No heat at night is an emergency call, and the price is flat-rate and approved first.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- What a furnace ignitor does
- Signs of a furnace ignitor not working
- Why a furnace ignitor fails
- Furnace ignitor not working, or another fault?
- Hot surface ignitors, spark ignition and standing pilots
- What you can safely check yourself
- Furnace ignitor not working: why replacement is a technician’s job
- What a technician does on an ignitor call
- A furnace ignitor not working in cold weather
- Gas smell and carbon monoxide safety
- No heat while you wait for a repair
- Reducing the odds of another ignitor failure
- Furnace ignitor not working: common questions
What a furnace ignitor does
The ignitor is the part that lights the gas. On most modern furnaces it is a hot surface ignitor, a small ceramic element that heats until it glows orange-hot, hot enough to ignite the gas when the valve opens. Without it, the burners never light and the furnace can’t make heat.
It works as one step in a sequence. The thermostat calls for heat, the inducer fan starts and clears the exhaust, the pressure switch confirms the draft, the ignitor heats, the gas valve opens, the burners light and the flame sensor proves the flame. If any step fails, the furnace stops and tries again.
Signs of a furnace ignitor not working
The classic sign is a furnace that starts up, runs the inducer fan and then goes quiet without ever producing flame. The ignitor is brittle, wears with every cycle and often fails without warning, so the first sign is frequently the first cold night of the season.
- The thermostat calls for heat, the inducer runs, but no flame appears
- No orange glow at the burners, if there is a viewing window
- The furnace tries two or three times, then stops and locks out
- The blower runs but the air stays cold
- A blinking status light on the control board
- It lights sometimes and not others, which is typical of a cracked ignitor
A flashing light is the furnace telling the technician what it saw. The code list is usually on a label inside the furnace door or in the manual, and the technician reads it on site.
Why a furnace ignitor fails
An ignitor wears out because of the extreme heating and cooling it goes through every cycle. Each start takes it from room temperature to glowing hot, and the ceramic slowly weakens, develops tiny cracks and eventually breaks or can’t heat enough.
Anything that makes the furnace start more often shortens its life, which is why short cycling is hard on ignitors. Other causes include voltage problems, dirty burners, a power surge, a touch from an oily hand when it was last replaced and the simple fact of age. Many ignitors last several years, but there’s no fixed number.
Furnace ignitor not working, or another fault?
Several faults look like a bad ignitor, which is why guessing leads to wasted parts. The pattern of what the furnace does helps narrow it down, and the table shows common look-alikes. A technician confirms the cause by testing the ignitor and the other parts in sequence.
| What you notice | Likely cause | Who fixes it |
|---|---|---|
| Inducer runs, no glow, no flame | Bad ignitor, or the board not powering it | Technician |
| Inducer never starts | Inducer motor, board or power fault | Technician |
| Inducer runs, then stops without ignition | Pressure switch, blocked vent or drain | Check the vent pipes outside; then technician |
| Glows, burners light, then go out in seconds | Dirty or failing flame sensor | Technician |
| Glows but no flame | Gas supply, valve or burner problem | Technician |
| Nothing at all, screen blank | Thermostat, switch or breaker | You first: check them once |
Hot surface ignitors, spark ignition and standing pilots
Not every furnace lights the same way. Most modern furnaces use a hot surface ignitor, some use a spark ignitor that clicks and sparks like a gas grill, and older ones keep a small standing pilot flame burning all the time. The symptoms differ slightly, but the cause is the same: nothing lights the gas.
If your furnace has a standing pilot, it may have blown out, and the label on the furnace explains how to relight it. Follow those steps only, and stop if it won’t stay lit or you smell gas. The pilot going out repeatedly is a fault, not something to keep forcing.
What you can safely check yourself
A few checks rule out the simple causes, and they take only a few minutes. Stick to the list. The ignitor sits in a sealed burner compartment, so leave the furnace doors and covers where they are and don’t touch anything that isn’t on the list below.
- Thermostat set to Heat, a setpoint above room temperature and fresh batteries if it takes them
- The furnace service switch on, and the breaker not tripped (reset it once if it is)
- A clean filter, since a restricted furnace can lock out
- Snow, ice and frost cleared by hand from the outdoor intake and exhaust pipes
- One reset: service switch off, wait about 30 seconds, then on
If it still won’t light after one reset, leave it alone. Repeated attempts aren’t harmless, since each failed start is a lockout in waiting. Our furnace not turning on guide covers other no-start causes.
Furnace ignitor not working: why replacement is a technician’s job
Video guides make the swap look easy, but it is gas work. The ignitor is inside the burner compartment next to the gas manifold and burners, so changing it means removing covers around live gas equipment. The part itself is fragile, and even skin oil from a fingertip can shorten its life.
There is also the question of why it failed. A technician tests the ignitor’s resistance and the current it draws, which tells a failing part from a board problem, and checks the burners, gas valve and flame sensor so a new ignitor isn’t killed by an underlying fault. The right replacement matches the furnace model.
What a technician does on an ignitor call
A TSSA-certified gas technician watches the furnace go through its start-up sequence, because the exact point where it stops tells them where to look. They test the ignitor, the pressure switch and venting, the gas valve and the flame sensor, and read the board’s fault history.
If the ignitor is the problem, they fit the correct part, then run the furnace through a full cycle to confirm the flame, the flame signal and the safety controls. The price is quoted flat-rate for your approval first, and our written workmanship warranty covers the repair.
A furnace ignitor not working in cold weather
Cold nights are when ignitors fail most often, because the furnace runs longest and weak parts are put to the test. A cracked ignitor may light for weeks in fall and give out in the first deep freeze. The furnace is also called on more often in a cold stretch, so each start adds wear.
In winter, rule out the vent too. Ice or snow on a high-efficiency furnace’s plastic vent pipes keeps the pressure switch from closing, so the ignitor never even gets its turn. Our frozen furnace vent pipe guide shows how to clear them safely by hand.
Gas smell and carbon monoxide safety
A furnace that tries to light and can’t is working as designed, but gas safety still matters. If the furnace has been trying to start and you smell gas, the gas valve may have opened without ignition. Treat it as a leak, whatever the furnace is doing, and leave.
- Gas smell: go outside without flipping switches or using a phone inside, then call Enbridge Gas at 1-866-763-5427.
- Carbon monoxide alarm sounding: get everyone, pets included, out of the house and dial 911.
- Never use a lighter or match to light a furnace burner. Stop and call.
Enbridge shares natural gas safety (opens in a new tab) advice. Under Ontario’s Fire Code, homes with fuel-burning appliances, fireplaces or attached garages need carbon monoxide alarms by every sleeping area and, since January 1, 2026, on every storey. The province’s carbon monoxide safety (opens in a new tab) page has the details.
No heat while you wait for a repair
A furnace that won’t light on a cold night is an emergency worth treating that way. Close doors to unused rooms, add layers and blankets, and keep the family in the warmest room. Our emergency furnace repair line is open 24/7, and technicians go out day or night.
Don’t light a gas oven or burner for heat, and be careful with portable heaters. If the house will be cold for hours, open cabinet doors under sinks on exterior walls so warmer air can reach the pipes.
Reducing the odds of another ignitor failure
You can’t stop an ignitor wearing out, but you can avoid shortening its life. Keep the filter clean so the furnace doesn’t overheat and cycle, fix short cycling early and make sure the furnace is the right size. A fall furnace maintenance visit tests the ignitor and checks its resistance before it fails.
Members of our maintenance plan get a fall furnace tune-up and a spring AC visit with priority booking, so a weak ignitor is more likely to be found in October than on a January night.
Furnace ignitor not working: common questions
How do I know if my furnace ignitor is bad?
The typical pattern is a furnace that calls for heat, runs the inducer fan, and then never lights, with no glow and no flame, before locking out. Only a technician can confirm it, because a pressure switch, flame sensor or board fault can look the same. They test the ignitor before replacing anything.
Can I replace a furnace ignitor myself?
It isn’t a homeowner job. The ignitor is in the sealed burner compartment beside the gas manifold, the part is fragile, and the cause of the failure still has to be found. Gas work is regulated by the TSSA and done by certified gas technicians. Call us rather than opening the furnace.
How long does a furnace ignitor last?
There is no fixed lifespan. Hot surface ignitors are wear parts that weaken with each heating cycle, and many last several years, but they can crack sooner, especially on furnaces that short cycle. A tune-up can catch a weakening one before it fails on a cold night.
Why does my furnace click but not light?
Clicking can be a relay, or the spark on a furnace with spark ignition. If it clicks and never lights, the ignitor or spark may be failing, the gas may not be reaching the burners, or the board isn’t completing the sequence. A technician finds which step stops.
What is the difference between the ignitor and the flame sensor?
The ignitor lights the gas, and the flame sensor proves the flame is burning. A bad ignitor means no flame at all. A dirty flame sensor means the burners light and then go out within seconds. They are different parts, and a technician tests both.
Is it dangerous if the ignitor isn’t working?
Not in itself. The furnace simply won’t light, which is a safety feature. The danger is a gas smell or an attempt to light the furnace by hand, so never use a flame. If you smell gas, leave the house and call Enbridge Gas from outside.
Will resetting the furnace over and over fix a bad ignitor?
No. One reset is fine, and it clears a temporary lockout. A weak or cracked ignitor won’t fix itself, and repeated resets just repeat failed start attempts. After one reset that doesn’t help, leave the furnace off and book a technician.
Who can fix a furnace ignitor that isn’t working in the GTA?
Assurance HVAC Heating & Cooling repairs furnaces in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. Our TSSA-certified gas technicians service all major brands, we’re open 24/7 for no-heat calls, and you approve a flat-rate price before any work starts.
Still no heat? We’ll call you back to book a technician.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
