
Furnace installation in Richmond Hill
(647) 905-9241Open 24/7, day or night
For furnace installation in Richmond Hill, Assurance HVAC Heating & Cooling of Richmond Hill takes on everything from replacing an aging furnace in a Westbrook or Doncrest two-storey to putting a compact high-efficiency unit into a Langstaff townhome. Every new furnace is sized from a heat-loss calculation of the house as it is now, our TSSA-certified gas technicians do the gas work, and you approve one flat price before anything starts. If the furnace you have might still be worth fixing, our furnace repair team will say so plainly.
Key takeaways
- New and replacement furnaces across Richmond Hill, sized with a heat-loss calculation.
- Gas connections by TSSA-certified technicians, with WSIB coverage and full insurance.
- One flat-rate price covers the whole job, approved before installation day.
- Most straightforward swaps take one day, with permits, inspections and haul-away handled.
- Each installation is backed by a written workmanship warranty. Book the home visit by form or phone.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Richmond Hill service team.
On this page
- When does furnace installation in Richmond Hill make sense?
- Sizing a new furnace for the house you have now
- Single-stage, two-stage or modulating for a two-storey home
- High-efficiency furnace ratings: AFUE, condensing and ECM
- Venting changes in older Richmond Hill homes
- Checking the original ductwork before the swap
- Replacing the furnace and air conditioner together
- Adding a cold-climate heat pump to the new furnace
- New furnaces for Richmond Hill townhomes and condos
- Furnace installation in Richmond Hill: the day itself
- Furnace installation in Richmond Hill: what sets the price
- Questions to ask any installer before you sign
- After the install: registration, warranty papers and tune-ups
- Furnace installation questions from Richmond Hill homeowners
When does furnace installation in Richmond Hill make sense?
A replacement makes sense once a furnace reaches 15 to 20 years and needs a major part, when it has needed a technician every winter lately, or when some rooms never warm up however long it runs. Plenty of Richmond Hill homes from the 1980s to the 2000s are there now, often with an air conditioner just as old.
- A heat exchanger crack, meaning the furnace must stay off
- A failed control board, inducer or blower motor on a furnace past 15 years
- Repair calls in each of the last few winters
- Gas bills creeping up while your settings stay the same
- A top floor that never catches up, or short cycling all day
One sign alone doesn’t settle it. We diagnose first, and when fixing the old furnace is the smarter spend, we say so.
Sizing a new furnace for the house you have now
Sizing starts with a heat-loss calculation: an estimate of the heat your house gives up on the coldest days, based on floor area, insulation, windows, air leakage and layout. The furnace that came with the house may no longer match it, especially after new windows, extra attic insulation or a finished basement.
An oversized furnace overshoots, shuts off and restarts minutes later, which wears it out and shortchanges rooms at the ends of the duct runs. An undersized one can’t keep pace in a deep freeze. Richmond Hill homes also change: a basement apartment, an addition over the garage or a rebuilt Richvale custom home can need a very different furnace.
Single-stage, two-stage or modulating for a two-storey home
Staging decides how a furnace delivers its heat. A single-stage furnace burns at 100% every time the thermostat calls. Two-stage models start on a lower fire and step up only in deep cold. Modulating models vary their output in fine increments, so they run long, quiet cycles that hold the temperature steadier from floor to floor.
| Type | How it runs | Upstairs and down | Fits best |
|---|---|---|---|
| Single-stage | Full fire every cycle | Bigger swings between floors | Smaller homes, tighter budgets |
| Two-stage furnace | Low most of the time, high in deep cold | Longer cycles even out the floors | Many two-storey family homes |
| Modulating furnace | Fine steps that follow the heat loss | The steadiest temperatures | Larger homes and open layouts |
Add a variable-speed ECM blower to either a two-stage furnace or a modulating furnace, and the gentle, steady airflow helps upper floors. In Bayview Hill and Oak Ridges, where big two-storey houses tend to overheat upstairs in July, the same blower helps the air conditioner too.
High-efficiency furnace ratings: AFUE, condensing and ECM
Condensing furnaces are the high-efficiency option, rated 90% AFUE or higher, and new gas furnaces sold in Canada today are rated 95% AFUE or more. AFUE is the share of the gas burned over a season that ends up as heat in your home, and condensing models get there by cooling the exhaust until water forms, recovering heat a mid-efficiency furnace sends up the chimney.
The blower matters too. An ECM, or electronically commutated motor, draws less electricity than the older PSC motors in many original furnaces, and variable-speed versions ramp up and down quietly. ENERGY STAR Canada (opens in a new tab) explains what the efficiency label on a high-efficiency furnace means.
Venting changes in older Richmond Hill homes
Switching to a condensing furnace means new venting. Instead of a metal pipe into the chimney, it vents through plastic pipe, usually a separate intake and exhaust, to an outside wall, plus a drain for the condensate it produces. Where those pipes exit takes planning on an older house.
Older homes near Mill Pond and the remaining post-war houses in Richvale are more likely to still have a chimney-vented furnace. The gas code sets minimum distances between the vent ends and nearby windows, doors, the gas meter and the ground, so we plan the route before quoting. In newer homes that already have plastic venting, we check that it meets current code for reuse.
Where a gas water heater shares that chimney, moving the furnace to PVC leaves the heater venting by itself through a flue that may be too big for it. Any liner or venting change goes in the quote, so a rented tank can be raised with its owner early.
Checking the original ductwork before the swap
A new furnace usually ties into the ducts you already have through fresh supply and return transitions, but original ductwork deserves a look first. Many two-storey Richmond Hill homes in Westbrook, Rouge Woods, Devonsleigh and Doncrest still use the ducts the builder put in, and some were laid out mainly for heating.
- A missing or undersized upstairs return, which starves the blower and unbalances the floors
- Leaky joints at the trunk and plenum, sending air where it isn’t needed
- Supply runs added in a basement renovation without a matching return
- Dampers closed years ago and forgotten
Anything that would hold the new furnace back is listed in the quote, so you can decide before approving.
Replacing the furnace and air conditioner together
Central air shares the furnace’s blower, and its coil sits right on top of the furnace, so matching matters. In many Richmond Hill homes the two went in together and are wearing out together. Replacing both in one visit means one installation, one set of coil and plenum connections, and equipment designed as a pair.
If the AC is 12 to 15 years old or still runs on R-22, which is no longer produced, price it alongside the furnace. If it has good years left, we say so and match the new furnace to it.
Adding a cold-climate heat pump to the new furnace
Instead of a new air conditioner, you can pair the new furnace with a cold-climate heat pump. It does the cooling in summer and carries most of the heating load, and the furnace takes over on the coldest days. That makes sense where the AC is due at the same time, a situation many Richmond Hill homeowners are in now.
Our heat pump installation page explains sizing. Eligible heat pumps can earn a rebate through Ontario’s Home Renovation Savings Program, and what a household receives varies with the house and how it’s heated now. Our rebates page explains how to check.
New furnaces for Richmond Hill townhomes and condos
Townhomes and low-rise condos along Yonge Street and near Langstaff usually have a small mechanical closet rather than a basement furnace room. We measure the space and the vent route before quoting, then look at compact high-efficiency furnaces, fan coils or a heat pump, depending on what fits.
Condo boards and managers often set rules for equipment changes and trades, so check early.
Furnace installation in Richmond Hill: the day itself
Most straightforward furnace replacement jobs in Richmond Hill finish in one day. After covering the floors, the crew takes out the old furnace, installs and connects the new one, and tests it until combustion, gas pressure, temperature rise and airflow all read where they should. Before leaving, the technician walks you through the filter, thermostat and condensate drain.
- The gas valve and power are turned off before the old furnace and its vent connector are removed.
- The new furnace is set level and tied into the supply and return ducts.
- New venting runs to the outside wall, and the drain goes to a floor drain or pump.
- Every gas joint is leak tested before the furnace is commissioned and run through full cycles.
- We haul away the old unit and all the packaging.
We handle the permits and inspections the job needs. Only technicians certified under the TSSA (opens in a new tab), Ontario’s fuel safety regulator, make the gas connections. Once the furnace runs, test your carbon monoxide alarms: Ontario requires one next to each sleeping area and, since January 1, 2026, on every storey of a home with a fuel-burning appliance, a fireplace or an attached garage.
Furnace installation in Richmond Hill: what sets the price
Furnace installation cost comes down to capacity, efficiency and staging, the venting and duct changes needed, any work on the AC coil, and how easy the furnace room is to get into. It varies too much between Richmond Hill houses to list prices, so after the home visit you get one flat price for the whole job.
| Factor | What it means for the job |
|---|---|
| Capacity | Set by the heat-loss calculation. Bigger costs more and often runs worse. |
| Efficiency and staging | Modulating furnaces and variable-speed blowers cost more upfront than single-stage models. |
| Venting | A first switch from chimney to PVC, a long pipe route or a water heater liner. |
| Ductwork | A new plenum, an added upstairs return or resized runs. |
| Cooling | Matching or replacing the AC coil, or adding a heat pump at the same time. |
| Access and extras | Finished basements, narrow stairs and closets add time, as do a humidifier or new thermostat. |
The flat price covers the job as quoted, removal of the old furnace included, and it doesn’t change partway through.
Questions to ask any installer before you sign
When you compare quotes, check that every installer is pricing the same furnace and the same work. Ask for the model number, AFUE, staging and blower type, and whether a heat-loss calculation set the size. A cheaper quote may skip the venting, the drain, permits or removal of the old unit, so read what’s included.
- Was the size calculated for this house, or copied from the old label?
- Are venting, the drain, permits, inspection and haul-away all listed?
- Who does the gas work, and do they hold TSSA certification, WSIB coverage and insurance?
- What does the written workmanship warranty cover?
Ask us the same questions. Our HVAC contractor in Richmond Hill page covers local homes and systems.
After the install: registration, warranty papers and tune-ups
A new furnace comes with paperwork worth keeping. Register it with the manufacturer within the time its warranty card allows, and file the invoice alongside it. Manufacturers often want to see a maintenance history before covering a part, so a yearly service record helps protect that coverage.
Our own written workmanship warranty applies to the installation work. A fall furnace maintenance visit before each Richmond Hill heating season keeps the new furnace clean and confirms the drain, venting and installation-day settings still check out.
Furnace installation questions from Richmond Hill homeowners
We live in Westbrook. Can our furnace be replaced in one day?
Usually, yes. Most like-for-like swaps are done in one day, including removing the old furnace, connecting the new one and testing it. A first move from chimney venting to PVC, ductwork changes or a finished basement that hides the ducts can add time. You get the expected timeline with your quote.
What size furnace does a two-storey Richmond Hill home need?
There’s no standard size for furnace installation in Richmond Hill, even for similar houses on one street. A heat-loss calculation weighs square footage, insulation levels, window area, draftiness and any finished space, then sets the capacity needed on the coldest days. Many original furnaces were oversized, so the replacement may well be smaller.
Is a modulating furnace worth it in a larger home?
In bigger Richmond Hill two-storeys, like many in Bayview Hill, Oak Ridges or Richvale, a modulating furnace with a variable-speed blower makes the biggest comfort difference, since its long, gentle cycles keep both floors near the setpoint. In a smaller townhome, a two-stage model often gives most of that benefit for less. We price both side by side.
Will a new furnace fix our hot upstairs in summer?
Not on its own. A hot second floor usually comes from ducts and returns laid out for heating, not the furnace. A new furnace with a variable-speed ECM blower helps by moving air more steadily, and an added upstairs return or rebalanced dampers can do the rest. We check airflow at the home visit and tell you what would help most.
Can a furnace be replaced in January?
Yes. Cold weather doesn’t stop an installation in Richmond Hill. The house goes without heat only for the stretch between the old furnace coming out and the new one firing up, normally the same day. If your furnace has already quit, call us, since a technician comes out day or night for no-heat calls and a repair may hold you over.
Should we replace the furnace before finishing the basement?
If the furnace is 15 years or older, it’s worth considering. Replacing it before the drywall goes up gives easier access, lets the heat-loss calculation include the finished space, and makes it simpler to add returns or supply runs for the new rooms. If the furnace has good years left, we can plan duct changes now and the swap later.
How do you choose the brand for a new furnace?
We service all major brands, but a recommendation doesn’t start from a brand name. The model we suggest for a Richmond Hill home comes after the heat-loss calculation and the duct and venting checks, because sizing and setup affect comfort as much as the badge.
Is furnace installation available in Oak Ridges and Langstaff?
Yes. Furnace installation in Richmond Hill covers every neighbourhood, from Oak Ridges, Jefferson and North Richvale to Crosby, Doncrest and Langstaff, and we also install in nearby Markham, Vaughan and North York. Send the request form or call the local number on this page, and we’ll book the home visit in a two-hour window with a text when we’re heading over.
Need furnace installation in Richmond Hill? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
