Skip to content
Gas furnace and water heater in a home basement
Brands we repair

Bryant furnace repair in Toronto

(647) 692-0819Open 24/7, day or night

Bryant furnace repair covers a wide range of equipment, from a single-stage Legacy unit to a variable-speed Evolution model. We repair Bryant furnaces across Toronto and the GTA as an independent contractor. This page explains how the lines differ, which parts fail and what Bryant itself tells owners to check. Our general process is on furnace repair in Toronto.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Bryant Canada lists Evolution, Preferred and Legacy furnace lines, from modulating down to single-stage.
  • Bryant advises monthly changes for one-inch filters and roughly every other month for two-inch pleated ones.
  • The rating plate is inside the unit, on the upper-left side behind the front door.
  • TSSA-certified gas technicians, open 24/7, flat-rate price approved before work.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Who makes Bryant furnaces, and which lines are sold
  2. Evolution, Preferred and Legacy: reading what you own
  3. Bryant furnace repair when the igniter or flame sensor is the problem
  4. Why filters matter on a Bryant furnace
  5. Checks before you call for Bryant furnace repair
  6. Common repairs on Bryant furnaces
  7. Connex controls and InteliSense: what to tell the technician
  8. Where to find the Bryant rating plate and what it tells us
  9. Bryant furnace codes: code 32, code 33 and the rest
  10. Repair or replace a Bryant furnace
  11. Gas smell and carbon monoxide: what to do first
  12. Booking a Bryant furnace visit in the GTA
  13. Bryant furnace repair questions

Who makes Bryant furnaces, and which lines are sold

Bryant is a Carrier Global brand, which makes it a sister brand of Carrier, Tempstar and KeepRite. We treat each brand’s furnace on its own terms and make no claim about shared parts.

Bryant Canada’s furnace page lists three lines: Evolution, Preferred and Legacy. The names matter when you call, because they tell us roughly how many stages the gas valve has and whether the blower is variable-speed.

Evolution, Preferred and Legacy: reading what you own

Bryant’s Canadian listing puts modulating and two-stage models in Evolution, two-stage and one variable-speed model in Preferred, and a single-stage furnace in Legacy. All the figures below are the maker’s own and are given as “up to” ratings.

Bryant Canada furnace lines, as the maker lists them
LineWhat Bryant listsRepair angle
EvolutionModulating (up to 98.5% AFUE) and two-stage (up to 96.7% and 97.0%), all variable-speedGas valve and blower motor tests, plus the system control
PreferredTwo-stage (up to 96.7% and 97%) and a variable-speed single-stage valve (up to 97%)Staged valve checks and ECM blower diagnosis
LegacySingle-stage, up to 97% AFUEA simple start-up sequence, so faults are quick to isolate

Bryant furnace repair when the igniter or flame sensor is the problem

A furnace that clicks, glows or ignites and then shuts off within seconds is usually telling you about ignition. Bryant says the 987M uses a pilot-free PerfectLight hot surface igniter (a US site). A hot surface igniter is a fragile part that wears over years of heating cycles.

A Bryant furnace igniter that has cracked or weakened won’t light the burners. A flame sensor that has gone dull with residue will let the flame start and then cut the gas. We test both with the furnace running before we replace anything.

Why filters matter on a Bryant furnace

Bryant Canada’s troubleshooting page advises replacing one-inch filters monthly and two-inch or high-capacity pleated filters about every other month. A restricted filter starves the furnace of air, and the result can be a limit switch that trips, a cold house and a blower motor working too hard.

If the Bryant furnace filter is clean and the problem continues, the cause is often further in. Dirty blower wheels, closed registers and blocked returns are common in GTA homes with finished basements and long duct runs.

Checks before you call for Bryant furnace repair

Bryant’s own troubleshooting advice starts with the breakers and the furnace switch, a light-style switch on a gray box at the furnace. We suggest the same order, then a few more checks that don’t involve opening the furnace.

  • Set the thermostat to Heat, a few degrees above the room reading.
  • Check the breaker, then the furnace switch.
  • Change a dirty filter and make sure the door is closed all the way.
  • On a high-efficiency model, clear snow from the outside intake and exhaust pipes by hand.
  • Try one reset. If the furnace locks out again, stop and call.

Common repairs on Bryant furnaces

Most calls involve one of a handful of parts, and which one depends on the symptom. We work through the start-up sequence in order so that we replace the failed part and not a healthy neighbour.

  • Inducer motor or pressure switch: the furnace starts, then the burners never light.
  • Limit switch: the burners shut off while the blower keeps running.
  • Blower motor and ECM module: weak airflow, or noise from the blower cabinet.
  • Control board: lockouts, no response, or intermittent faults.
  • Condensate trap and drain: water around the furnace, or a pressure switch tripped by a blocked line.

Connex controls and InteliSense: what to tell the technician

Bryant says its Evolution 987M pairs with the Evolution Connex System Control, and that its InteliSense feature collects equipment performance data once the owner grants permission and a Connex control is paired (US site). We can’t confirm that the Connex name applies to every Canadian model.

So tell us which wall control you have, and whether it was installed with the furnace or added later. A mismatched control is easy to fix once we know it is there.

Where to find the Bryant rating plate and what it tells us

Bryant Canada says the model number is on a rating plate sticker inside the unit. With the front door off, the plate is on the upper-left side. Because that door has a safety switch and sits close to live parts, we suggest asking a technician to photograph it during a visit.

For fault information, see the code table in the next section. We read the furnace’s status on site and explain it in plain terms.

Bryant furnace codes: code 32, code 33 and the rest

Bryant’s 926TC, the Preferred two-stage furnace, flashes its status on an LED you can see through the sight glass in the door: the first digit counts short flashes, the second counts long ones. A display on the board adds a third digit. The table follows the service label in Bryant’s 926TC installation instructions (opens in a new tab), pages 56 and 76.

Only the two-digit major code shows through the glass. Other Bryant models may carry a different label, so compare the model number before relying on this list.

Bryant 926TC codes as Bryant prints them on the furnace service label
CodeWhat it meansWhat to do
13 (13.1)The limit, draft safeguard, flame rollout or blocked vent switch stayed open over 3 minutes; a 3 hour lockout followsCall a technician
14 (14.1)No flame proven in 4 ignition attempts; a 3 hour lockout followsBook a repair
15 (15.1)Blower lockout: the control sensed no blower speedBook a repair
24 (24.1)Fuse fault on the controlBook a repair
31 (31.6)High-heat pressure switch open; wind, a restricted vent or a blocked condensate drain are possible causesClear snow from the outdoor vent and intake by hand; book a repair if it repeats
32 (32.2)Main pressure switch (LPS) open over 5 minutes, or reopened; the inducer waits 15 minutes before another tryCheck the outdoor pipes for snow or debris, then book a repair
33 (33.1)The main limit circuit opened at the limit or flame rollout switch; the guide lists a dirty filter or restricted ducts firstChange a dirty filter, then call a technician
34 (34.1)Ignition fault across four trials in a rowBook a repair
41 (41.1)No blower RPM at start-upBook a repair
46 (46.1)Power dipped for a moment; heat resumes once it steadiesNo action needed unless it repeats
Rapid flash (10.1)Power polarity is reversed at the furnace, so it won’t heatBook a repair

Note the flash count and what the furnace was doing. The control holds its last seven faults for 72 hours of powered running, so our TSSA-certified gas technicians can read that history on site and test the part behind the code before replacing it.

Repair or replace a Bryant furnace

A gas furnace typically lasts 15 to 20 years. Within that range, a single failed part is normally worth repairing. A cracked heat exchanger, or repair bills that keep returning, change the math.

Repair or replace, by the age and fault
Age and faultOur usual advice
Under 10 years, igniter or sensorRepair
10 to 15 years, board or motorRepair, and compare the cost to new
15 to 20 years, second major repairPrice a replacement alongside the repair
Any age, cracked heat exchangerReplace

For installation questions, see furnace installation in Markham.

Gas smell and carbon monoxide: what to do first

Gas smell means leave the house and call Enbridge Gas on 1-866-763-5427 once you’re outside. A CO alarm means everyone gets out and someone calls 911. Details are on the Enbridge Gas safety page (opens in a new tab).

Booking a Bryant furnace visit in the GTA

We serve Toronto, Vaughan, Richmond Hill, Mississauga, North York, Markham and Oakville. Booked visits get a two-hour arrival window and a text. After diagnosing the furnace, we quote a flat-rate price, and work starts only when you approve it. No heat overnight is an emergency: we’re open 24/7 and technicians go out day or night.

Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Bryant. Brand names are trademarks of their owners.

FAQ

Bryant furnace repair questions

Is Bryant the same as Carrier?

Bryant is a Carrier Global brand, so the two share a parent company. We don’t say they share factories or parts, because we have no source for that. We repair a Bryant furnace by its own model and condition, and confirm any part against the rating plate before we order it.

How often should I change a Bryant furnace filter?

Bryant Canada advises replacing one-inch filters monthly and two-inch or high-capacity pleated filters about every other month. Heavy dust, pets or renovation work may call for sooner changes. A clogged filter is a leading reason furnaces overheat, so it is the first check before any call.

My Bryant furnace clicks but won’t light. What is wrong?

Clicking then nothing often points to the igniter, the gas valve, a flame sensor or a pressure switch that won’t close. Check the filter and thermostat, try one reset, and then stop. Repeated tries won’t help, and a technician needs to test the furnace running.

Do you repair Bryant Evolution furnaces?

Yes. Our technicians work on Bryant furnaces in the Evolution, Preferred and Legacy lines, including variable-speed models. We are independent and not affiliated with Bryant. We test the furnace together with its wall control; Bryant’s US site says Evolution models such as the 987M pair with the Evolution Connex System Control.

Where do I find the model number on a Bryant furnace?

Bryant Canada says it is on a rating plate sticker inside the unit, on the upper-left side once the front door is off. Because the door has a safety switch and the furnace holds live parts, we suggest having your technician photograph it, then filing the photo with your paperwork.

What does a Bryant furnace flashing light mean?

The 926TC blinks its status through a small sight glass in the door, counting short blinks for the first digit and long blinks for the second. Code 32 is the main pressure switch staying open, often a vent or drain issue, and code 33 is an opened limit or rollout switch. Other Bryant models carry their own label.

What is InteliSense on a Bryant furnace?

Bryant describes InteliSense as a feature that collects equipment performance data, and says it needs a Connex control and the owner’s permission to share data. It is mentioned on a US product page. Ask us if you aren’t sure your system has it, and we will look at the controls.

Is Bryant furnace repair covered by warranty?

It depends on the model, the install date and whether the unit was registered, so check your paperwork and Bryant Canada’s warranty page. We don’t perform warranty work for the maker. Our own repairs carry a written workmanship warranty, and our maintenance plan can help with maintenance records.

Book a visit

Need Bryant furnace repair? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy