Skip to content
Gas furnace and water heater in a home basement
Brands we repair

Napoleon furnace repair in Toronto

(647) 692-0819Open 24/7, day or night

Napoleon is an Ontario company, headquartered in Barrie. We handle Napoleon furnace repair across Toronto and the GTA, and we explain the fault and the price before any work begins. Our wider furnace repair in Toronto page covers what a visit involves.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Napoleon is the brand of Wolf Steel Ltd., headquartered in Barrie, Ontario.
  • We work on Napoleon furnaces, and we service all major brands.
  • Most no-heat faults come from ignition, airflow, venting or controls, whatever the brand.
  • Gas smell: leave and call Enbridge Gas. CO alarm: everyone out, call 911.
  • Open 24/7, with the flat-rate price approved by you before work starts.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Napoleon furnace repair across Toronto and the GTA
  2. About Napoleon and Wolf Steel
  3. What we will not guess about your Napoleon furnace
  4. Small furnaces, correct sizing and short cycling
  5. Why a Napoleon furnace won’t ignite or won’t stay on
  6. Checks you can make before calling for help
  7. Napoleon furnace codes: what 4 flashes and the others mean
  8. Napoleon furnace repair or replace
  9. Warranty and your paperwork
  10. If you smell gas or a CO alarm sounds
  11. Booking a Napoleon furnace repair across the GTA
  12. Napoleon furnace repair questions

Napoleon furnace repair across Toronto and the GTA

Napoleon gas furnaces are part of our regular work around Toronto and the wider GTA, whether one will not light or keeps cycling on and off. Our gas technicians hold TSSA certification, and our company is independent, with no tie to any one furnace maker.

About Napoleon and Wolf Steel

Napoleon is the brand of Wolf Steel Ltd., a privately held, family-run company headquartered in Barrie, Ontario. It began in 1976 as Wolf Steel and adopted the Napoleon name in 1995.

HVAC is one of its main manufacturing divisions.

What we will not guess about your Napoleon furnace

Apart from the installation manual cited in the code section below, we did not verify Napoleon’s product details, so we do not quote efficiency ratings or ignition types here. Your furnace’s label and manual are the source for those, and our technicians read them on site.

That is a practical point too. A furnace can be single-stage, two-stage or modulating, with a standard or high-efficiency design, and each behaves differently. We confirm which you have before we decide what to test.

Small furnaces, correct sizing and short cycling

Napoleon developed a 30,000 BTU gas furnace in 2013. Whatever your size, a furnace that is too big for the home can short cycle, shutting off before the house is evenly warm.

Short cycling can come from an oversized furnace, but also from a dirty filter, a failing flame sensor or a blocked vent, so size is only one suspect. A proper heat-loss calculation is how we judge fit if a replacement ever comes up. Our guide to furnace short cycling lists the causes.

Why a Napoleon furnace won’t ignite or won’t stay on

A furnace that does not light, or lights and then quits, is the most common no-heat call. The cause is usually one of a few parts, and the order a technician checks them in matters.

No-heat symptoms on a gas furnace and the parts behind them
SymptomParts to checkCommon cause
Nothing happens when heat is calledThermostat, door switch, control board, fusePower or control problem
Fan starts, no flameHot surface igniter, gas valve, pressure switchIgnition fault or a blocked vent
Flame starts, then goes outFlame sensor, burners, gas supplySensor coated or burners dirty
Shuts off after a few minutesLimit switch, filter, blower, ventOverheating from poor airflow
Loud or uneven blowerBlower motor, ECM motor, wheelWorn motor or debris
Water near a high-efficiency unitCondensate trap, drain, pumpBlocked condensate drain

Checks you can make before calling for help

These steps are safe for any homeowner and use no tools at all. If the furnace is still off after you have tried them, leave the gas and electrical parts to a licensed technician.

  • Raise the thermostat above room temperature, set to Heat, and change dead batteries.
  • Confirm the furnace switch and the breaker are on.
  • Look at the filter, and change it if it is clogged.
  • Check that the furnace door is seated so its safety switch closes.
  • Clear snow, ice or a bird’s nest from outdoor vent pipes, by hand.
  • Reset once. A furnace that locks out again should stay off.

Napoleon furnace codes: what 4 flashes and the others mean

Napoleon’s Premium 9600 Series, the WPV-N two-stage furnaces from the WPV035T2AA-N to the WPV120T5BA-N, report faults by flashing a red LED on the control board. The meanings below are copied from section 19.5 of Napoleon’s WPV-N installation manual (opens in a new tab), page 63. Other Napoleon furnaces may use a different list.

Count the flashes between pauses and write the number down. The control also stores its last five fault codes and replays them, most recent first, when its push button is pressed, which our technician does on site.

Red status LED codes for the Napoleon WPV-N (Premium 9600 Series) only
CodeWhat it meansWhat to do
LED OFFNo power to the control, or the control found a hardware faultCheck the furnace switch and breaker; if the light stays off, book a repair
LED ONNormal operationNo action needed
1 FlashHigh limit switch open; the manual’s flowchart also waits here for a flame rollout resetLook at the filter, then call a technician
2 FlashesPressure switch open with the inducer running; the control stops the inducer for 60 minutesClear snow or debris from the outdoor intake and exhaust by hand, then book a repair
3 FlashesPressure switch closed while the inducer is offBook a repair
4 FlashesControl in a 1 hour lockout, reached after failed ignition trialsBook a repair
5 FlashesL1 and neutral polarity problemBook a repair
6 FlashesToo many limit trips within one call for heatCall a technician
7 FlashesPressure switch cycle lockoutBook a repair
8 FlashesLockout after too many flame dropouts, lasting 1 hourBook a repair
10 FlashesFlame present with the gas valve offCall a technician

Before we arrive, photograph the rating label and note the flash count and when the problem started. Our TSSA-certified gas technicians check the stored codes on site and test the switch or part a code points to before replacing anything.

Napoleon furnace repair or replace

Gas furnaces generally run 15 to 20 years, so the first question is how old yours is. A newer furnace with one failed part is nearly always worth repairing, while an old one with repeat faults is a conversation about replacement.

Weighing a repair against a new furnace
SituationUsually better toReason
Under 10 years, one failed partRepairParts still have years left
15 to 20 years, repeat faultsPrice a replacementRepairs add up on aging parts
Cracked heat exchangerReplaceA safety issue
Furnace too big for the houseFix the cause, or resize on replacementOversizing causes short cycles

See our repair or replace guide for a fuller walk-through.

Warranty and your paperwork

We could not verify Napoleon’s warranty rules, so please check the paperwork from your install and any registration you filed. Keep the model and serial numbers with your invoice, in a place you can find quickly.

Many manufacturer warranties ask for proof of regular maintenance, so look at yours. Ontario does not require yearly furnace maintenance by law. Our repairs carry a written workmanship warranty.

If you smell gas or a CO alarm sounds

When there is a gas smell, get out of the house straight away and call Enbridge Gas on 1-866-763-5427 from outside. When a carbon monoxide alarm goes off, bring everyone outdoors and call 911.

The Enbridge Gas safety page (opens in a new tab) covers what to do and what to avoid.

Booking a Napoleon furnace repair across the GTA

A booked visit starts with a text and a two-hour arrival window, and the technician quotes a flat-rate price for you to approve before any work. If the heat dies late at night, phone anyway: the line is answered around the clock and emergency calls go ahead of routine bookings.

Our service areas are Oakville, Mississauga, Toronto, North York, Vaughan, Markham and Richmond Hill. For Richmond Hill, see our furnace repair in Richmond Hill page for local detail.

Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Napoleon. Brand names are trademarks of their owners.

FAQ

Napoleon furnace repair questions

Who makes Napoleon furnaces?

Napoleon is the brand of Wolf Steel Ltd., a privately held, family-run company headquartered in Barrie, Ontario. It began in 1976 as Wolf Steel and took the Napoleon name in 1995. Beyond that, we rely on the label on your own furnace for specifics.

Do you repair Napoleon furnaces in Toronto?

Yes. Our technicians work on Napoleon furnaces in Toronto and the GTA, as on all major brands. The flat-rate price comes first and you approve it before any repair starts. If the heat goes out at night, the line is open 24/7.

Why won’t my Napoleon furnace ignite?

Usually the igniter, the flame sensor, a gas valve or a safety switch is involved, and a blocked vent can stop ignition too. Check the thermostat, switch, breaker and filter first. If it still will not light, call us rather than resetting repeatedly.

What does a Napoleon furnace flashing light mean?

On a Premium 9600 Series (WPV-N) furnace the red LED flashes a count. Four flashes means the control is in a 1 hour lockout after failed ignition trials, and one flash means the high limit is open. The table above lists every code. Other Napoleon models may differ, so check the label on your own furnace.

Can a furnace be too big for my house?

Yes. An oversized furnace heats the house quickly, shuts off and restarts often, which is called short cycling. It can wear parts and leave rooms uneven. Other faults cause the same symptom, so we check the filter, flame sensor and venting before blaming size.

Is Napoleon furnace repair worth it on an older unit?

It depends on age and the fault. A furnace under about 10 years with one failed part is usually worth fixing. Past 15 years, with repeat problems, a replacement price is worth comparing. You see the repair price before deciding.

Are you affiliated with Napoleon?

No. Our company is independent and services every major brand. Our technicians do work on Napoleon furnaces, but we have no connection to Wolf Steel and do not carry out its warranty work. What we do carries a written workmanship warranty.

Book a visit

Need Napoleon furnace repair? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy