
When a Lennox furnace stops heating, the fault can sit in the burner, the blower, a safety switch or the controls that tie them together. Our Lennox furnace repair covers Toronto and the GTA, and we explain the fault and the price before any repair starts. For the full range of what we fix, see our furnace repair in Toronto page.
Key takeaways
- We repair Lennox furnaces in Toronto and the GTA, and we service all major brands.
- Lennox communicating systems tie the furnace, thermostat and other parts together, so diagnosis covers the whole system.
- The serial number is on a label affixed to the furnace, handy when you call.
- Gas smell: leave and call Enbridge Gas. CO alarm: everyone out, call 911.
- Open 24/7, with a flat-rate price approved before any work begins.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- Lennox furnace repair in Toronto and the GTA
- Who makes Lennox, and which brands sit beside it?
- The furnace lines Lennox sells
- What changes when we service a Lennox communicating system
- Common Lennox furnace problems and what fixes them
- Safe checks before you call about your Lennox furnace
- Lennox furnace error codes: what E223 and the others mean
- Finding the Lennox serial number and model
- Lennox furnace repair or replace: how to decide
- Warranty and registration on a Lennox furnace
- Safety: gas smell and carbon monoxide
- What a Lennox furnace repair visit looks like
- Lennox furnace repair questions
Lennox furnace repair in Toronto and the GTA
We diagnose and repair Lennox gas furnaces in Toronto and the surrounding GTA, from a furnace that will not start to one that runs but blows cool air. Our gas work is done by TSSA-certified technicians, and you approve a flat-rate price before we begin.
We are an independent contractor. We service all major brands, and our technicians work on Lennox furnaces without being tied to any one maker.
Who makes Lennox, and which brands sit beside it?
Lennox International is based in Richardson, Texas. Its Home Comfort Solutions brands are Lennox, Armstrong Air, Ducane, AirEase, Concord Air, MagicPak and Allied Air, so a furnace with one of those names comes from the same company.
That tells you who owns the brand, not which parts any two models share. We never assume parts carry over, and we confirm what your unit uses from its own label before we order anything.
The furnace lines Lennox sells
On its US site, Lennox sorts residential furnaces into three series: Dave Lennox Signature, Elite and Merit. Series names and what is sold here may differ in Canada, so read this as a sketch of the range, not a list of what sits in your basement.
The Lennox US page shows the top Signature furnace as variable-capacity with AFUE up to 99.0%, and lists two-stage and single-stage models in the Elite and Merit series. Lennox describes its Precise Comfort feature as adjusting output in small increments and SilentComfort as ramping up gradually at startup. Those descriptions come from the maker’s US furnace page.
What changes when we service a Lennox communicating system
A communicating Lennox system uses a thermostat that talks to the furnace, so a fault can start in the controls rather than in a burner part. Lennox says its iComfort S30 thermostat is part of a communicating system and works with premium Lennox communicating equipment only.
Lennox also says the S30 monitors system operation and alerts the owner when a problem arises. If your thermostat is showing an alert, write down the message and when it appeared. It helps us start in the right place.
A variable-capacity or two-stage furnace adds more to check than a single-stage one, since the control board decides how hard the burner and blower should run. We test the controls, the safety switches and the blower together, not one part at a time.
Common Lennox furnace problems and what fixes them
Most Lennox furnace calls trace back to a short list of parts: ignition, airflow, venting and the control board. The table shows what you may notice and what a technician usually checks.
| What you notice | Parts we check | What it often means |
|---|---|---|
| Clicks, then no flame | Hot surface igniter, flame sensor, gas valve | Ignition part worn or sensor coated |
| Burner lights, then shuts off | Flame sensor, limit switch, venting | Sensor dirty or airflow blocked |
| Runs but blows cool air | Igniter, burner, gas supply, limit switch | Burner is not staying lit |
| Loud blower or weak airflow | Blower motor, ECM blower module, filter | Motor wear or restricted airflow |
| Water around the furnace | Condensate trap, drain line, pump | Drain blocked on a condensing model |
| Thermostat alert or no response | Control board, thermostat wiring, communication link | Controls fault or lost signal |
Weak ignition parts and a coated flame sensor are behind many furnaces that start and then quit. Our guide to a furnace that is not turning on walks through what each symptom points to.
Safe checks before you call about your Lennox furnace
A few checks take five minutes and need no tools. If none of them fix it, stop there and call us, since the rest of the work involves gas and electrical parts.
- Confirm the thermostat is set to Heat, the temperature is above the room reading, and any batteries are fresh.
- Check that the furnace switch near the unit is on and the breaker has not tripped.
- Replace a dirty filter. A clogged one can trip the limit switch.
- Make sure the furnace door is closed fully so its door switch makes contact.
- On a condensing model, clear snow or ice from the plastic intake and exhaust pipes outside, by hand only.
- Note any thermostat message, then try one reset. If it locks out again, leave it off.
Lennox furnace error codes: what E223 and the others mean
Newer Lennox furnaces report faults as a code on a small seven-segment display on the control board, beside a push button that recalls the last 10 codes. If the door has a viewing window, read it from outside. Keep the door on, since Lennox warns the blower access panel must be securely in place while the blower and burners run.
The codes below come from Lennox’s ML296UHVK installation instructions (opens in a new tab), form 508520-01, for a Merit series two-stage gas furnace. Other Lennox models, and older ones that flash a light instead of showing a code, use their own lists. A code tells you which part to test, not which part has failed.
| Code | What it means | What to do |
|---|---|---|
| E200 | Hard lockout: the flame rollout circuit is open, or opened earlier | Call a technician |
| E207 | The control reads the hot surface igniter as open | Book a repair |
| E223 | Low pressure switch failed open: it stayed open instead of closing | Book a repair |
| E224 | Low pressure switch failed closed: stuck shut | Book a repair |
| E227 | Low pressure switch opened during ignition or while running | Book a repair |
| E240 | Weak flame sensor signal while the burner runs | Book a repair |
| E241 | Flame is sensed out of sequence and is still present | Call a technician right away |
| E250 | Limit switch circuit open; after 3 minutes, a 1-hour lockout follows | Call a technician |
| E270 | Soft lockout: too many ignition retries with no flame sensed | Book a repair |
| E274 | Soft lockout: the limit kept opening or stayed open over 3 minutes | Call a technician |
| E292 | Blower motor cannot start: obstructed wheel or seized bearings | Book a repair |
| E311 | Warning only: heat is cut back to match restricted airflow | Replace the filter if it is dirty |
Write down the code, whether the furnace was lighting, running or idle, and how long it lasted. Our TSSA-certified gas technicians read the code on the control, then test the part it points to before replacing anything.
Finding the Lennox serial number and model
Lennox says serial numbers are printed on a label affixed to the equipment. Its warranty page shows formats such as ####A#####, A##A###### and AA##A#####. Have the model and serial number ready when you call, since the model also tells us which code list applies.
We don’t decode manufacture dates from the serial; the technician confirms the age on site. The label and your paperwork tell us what we need.
Lennox furnace repair or replace: how to decide
Age is the first question, because gas furnaces typically run 15 to 20 years. Fixing a younger Lennox is usually sensible. An older one that keeps needing parts is worth pricing against a new furnace.
| Situation | Usually better to | Why |
|---|---|---|
| Younger unit, one failed part | Repair | The remaining components have years left |
| 15 to 20 years, second repair in a season | Compare replacement | Wear is catching up with the parts |
| Cracked heat exchanger | Replace | A safety problem, not a repair job |
| Old single-stage unit and uneven rooms | Consider a two-stage or variable model | Better comfort and efficiency |
We give you the flat-rate repair price first, and we will tell you plainly when replacement is the better spend. Our repair or replace guide lays out the numbers to weigh.
Warranty and registration on a Lennox furnace
Warranty terms for Lennox equipment in Canada should come from Lennox’s own Canadian warranty information, so check it against your registration or install paperwork. Keep your invoice, the model and serial numbers and any registration confirmation together.
Every repair we do comes with a written workmanship warranty. It is separate from whatever the maker provides on the furnace itself.
Safety: gas smell and carbon monoxide
Smell gas? Walk out first, and phone Enbridge Gas on 1-866-763-5427 once you are outside. Leave switches alone and do not use a phone inside. A sounding carbon monoxide alarm means everyone goes outdoors and someone calls 911.
Any Ontario home with a fuel-burning appliance, a fireplace or an attached garage needs working CO alarms next to each sleeping area and, since January 1, 2026, on every storey, so press the test button on yours at the same time as the smoke alarms. The Ontario carbon monoxide safety page (opens in a new tab) explains where to place them.
What a Lennox furnace repair visit looks like
A booked visit starts with a text and a two-hour arrival window. The technician checks the thermostat, the safety switches, ignition and blower, finds the fault, and gives you a flat-rate price to approve before touching a part.
If the house has no heat, call at any hour: we are open 24/7 and a technician can be sent out in the night or on a weekend, with emergency calls taken first. We cover Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville, and you can start with our HVAC contractor in Vaughan page or the area nearest you.
Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Lennox. Brand names are trademarks of their owners.
Lennox furnace repair questions
Why is my Lennox furnace not heating?
Common causes are a failed igniter, a dirty flame sensor, a clogged filter that trips the limit switch, or a control or thermostat fault. Check the thermostat, the furnace switch, the breaker and the filter first. If it still will not heat, call us rather than resetting repeatedly.
Do you repair Lennox communicating furnaces?
Yes. Lennox says its iComfort S30 works with premium Lennox communicating equipment only, so we check the furnace and its controls as one system. Tell us what the thermostat displays when the problem happens, and we will start from there.
Where do I find the serial number on my Lennox furnace?
Lennox says serial numbers are printed on a label affixed to the equipment. If you can’t see it without removing a panel, leave it for the technician. Take a clear photo of it, since we can use it to confirm the model before the visit.
Is a Lennox furnace worth repairing?
It depends on age and the fault. A furnace under about 10 years old with one failed part is usually worth repairing. Past 15 years, or with a cracked heat exchanger, replacement deserves a look. We give you a flat-rate repair price first, so you can decide.
Can you fix a Lennox furnace at night or on a weekend?
Yes. Our line is answered 24/7 and technicians head out overnight and on weekends as well as weekdays. Emergency calls are handled ahead of the rest. For a Lennox furnace repair you hear the flat-rate price first, and nothing starts until you approve it.
Are you affiliated with Lennox?
No. We are an independent heating and cooling contractor and we service all major brands, including Lennox. Our technicians work on Lennox furnaces, but we have no link to the maker, and we do not do warranty work on its behalf.
What does a Lennox furnace error code mean?
It names the part or circuit the control flagged. Lennox’s ML296UHVK manual lists E223 as the low pressure switch failing open and E250 as the limit switch circuit open, and the table above covers more. Codes differ by model, so try one reset at most and call us if the code returns.
Need Lennox furnace repair? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
